NBE-5AC-Gen2 17dBi 8.5W 802.11ac Gigabit Wireless Bridge
UBNT high-power gigabit wireless bridge NBE-5AC-Gen2 802.11ac outdoor CPE wireless bridge wifi transmission coverage
Installation Requirements:
1.Pole-mounting: 7 mm socket wrench or screwdriver
2.Wall-mounting: wall fastener (not included)
3.Shielded Category 5 (or above) cabling with drain wire should be used for all wired Ethernet connections .
4.And should be grounded through the AC ground of the PoE.
5..Surge protection should be used for all outdoor installations.
6.We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the NanoBeam
7.And the other at the entry point to the building.
8.The ETH-SP will absorb power surges and safely discharge them into the ground.
|
Main Ethernet Port |
||
|---|---|---|
| This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. | ||
|
Reset Button |
||
| To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Adapter. | ||
|
Secondary Ethernet Port |
||
|
This Gigabit Ethernet port provides passthrough PoE to power and connect a 24V passive PoE device to the network.
|
||
|
Power LED |
||
| The Power LED will light blue when the device is connected to a power source. | ||
|
Main LED |
||
| The LED will light steady blue when an active Ethernet connection is made to the Main port and flash when there is activity. | ||
|
LAN2 LED |
||
| The LED will light steady blue when an active Ethernet connection is made to the LAN2 port and flash when there is activity. | ||
|
Signal LEDs |
||
| In airOS®, you can modify the threshold value for the wireless signal strength LEDs on the Wireless tab under Signal LED Thresholds. Each LED will light when the wireless signal strength is equal to or greater than the LED’s threshold value. |
Specification:
| NBE-5AC-Gen2 | |
|
Dimensions |
189 x 189 x 125 mm (7.44 x 7.44 x 4.92") |
|---|---|
|
Weight |
530 g (1.17 lb) |
|
Gain |
17 dBi |
|
Networking Interface |
(2) 10/100/1000 Ethernet Ports Wi-Fi for Management |
|
Enclosure |
Outdoor UV Stabilized Plastic |
|
Max. Power Consumption |
8.5W |
|
Power Supply |
24V, 0.5A Gigabit PoE Adapter (Included) |
|
Power Method |
24V Passive PoE In (Pairs 4, 5+; 7, 8 Return) |
|
PoE Passthrough |
24V Passive PoE Out (Pairs 4, 5+; 7, 8 Return) |
|
Wind Loading |
45.4 N @ 200 km/h (10.2 lbf @ 125 mph) |
|
Wind Survivability |
200 km/h (125 mph) |
|
Operating Temperature |
-40 to 80° C (-40 to 176° F) |
|
Operating Humidity |
5 to 95% Noncondensing |
|
Salt Fog Test |
IEC 68-2-11 (ASTM B117), Equivalent: MIL-STD-810 G Method 509.5 |
|
Vibration Test |
IEC 68-2-6 |
|
Temperature Shock Test |
IEC 68-2-14 |
|
UV Test |
IEC 68-2-5 at 40° C (104° F) Equivalent: ETS 300 019-1-4 |
|
Wind-Driven Rain Test |
ETS 300 019-1-4 Equivalent: MIL-STD-810 G Method 506.5 |
|
Mounting |
Pole-Mount (Kit Included) Wall-Mount (Not Included) |
|
ESD/EMP Protection |
± 24kV Contact/Air |
|
Certifications |
CE, FCC, IC |
| Operating Frequency (MHz) | ||||
|
Worldwide |
5150 - 5875 | |||
|---|---|---|---|---|
|
US/CA |
U-NII-1 |
5150 - 5250 | ||
|
U-NII-2A |
5250 - 5350 | |||
|
U-NII-2C |
5470 - 5725 | |||
|
U-NII-3 |
5725 - 5850 | |||
| Management Radio (MHz) | |
|
Worldwide |
2412 - 2472 |
|---|---|
|
US/CA |
2412 - 2462 |
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.