Double Row PHB Connector 2.00MM Pitch HCTL HC-PHB-2*17EY-05 for Electronic Device Connection

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification document details the 2.00MM PITCH PHB CONNECTOR DOUBLE ROW TYPE, part number HC-PHB - ****. It covers product performance, test methods, and inspection requirements for this series of connectors.

Product Attributes

Brand: (HCTLDZ)
Origin: China
Model: PHB (2.0) -05
Certifications: UL94V-O (for Housing Plastic and Plastic Wafer)

Technical Specifications

Item	Requirement	Test Mode
4. Appearance and Dimension
Appearance	Product surface without defect, dirt, crack, and mechanical damage; contact parts without rust, plating oxidation, or peeling.	General Principles
Dimension	According to drawings	General Principles
Exchangeable	Exchangeable with same specification products.	General Principles
3. Use Condition
Ambient temperature	-25 +85	General Principles
Applicable Wire Sizes	AWG #2228	General Principles
Applicable PC board thickness	1.6mm	General Principles
5. Material
Terminal Contact	Brass, Thickness: 0.50mm, Tin plating: 2.55 m	-
Housing Plastic	Nylon66, UL94V-O, Color: Nature	-
Plastic Wafer	Nylon66, UL94V-O, Color: Nature	-
Contact Pin	Phosphor bronze, Thickness: 0.2mm, Tin plating: 35 m	-
6. Electrical Performance
Rated Voltage	250V AC/DC	-
Rated Current	2A AC/DC	-
Withstand voltage	No breakdown or flashover	Apply 800V AC(rms)for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors
Contact Resistance	Initial value 20m	Apply a maximum voltage of 20mV and maximum current of 100mA to the mate connector (Does not include wire resistance)
Insulation Resistance	1000 M	Apply 500V DC(rms) for 1 minute between adjacent contacts to measure the insulation resistance
7. Mechanical Performance
Terminal crimping Wire strength	AWG#22: 50N, AWG#24: 30N, AWG#26: 20N, AWG#28: 13N	Axial pullout force at 25 3mm per minute
Fixed terminals And hole seat	12N	Terminal and hole seat mating pullout force at 25 3mm per minute along the wire direction
Single contact insertion force	5N	Housing together with terminal ends with wafer matched at a rate per minute to 253mm inserting force test
Seat pull-out force	15N	Exerts a force on the pin end at a rate per Minute 253mm until the needle exits seat
Durability	Contact Resistance 40m, Appearance: No damage	Mate connectors up 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test
Vibration	Current Discontinuity 1 micro second, Contact Resistance 40m, Appearance: No damage	Amplitude: 1.5mm p-p, Frequency: 10-55-10Hz/minute, Period: 2 hours for each direction (X, Y, Z axis)
8. Endurance Characteristics
Thermal Aging	Contact Resistance 40m, Appearance: No damage	Temperature: 852, Period: 96 hours continuously
Temperature Rise	-	Measure the temperature rise of contact when the maximum rated current is passed
Humidity	Contact Resistance 40m, Insulation Resistance 1000m, Appearance: No damage	Temperature: 402 C, Relative humidity: 90-95% (RH), Period: 96 hours continuously
Thermal Shock	Contact Resistance 40m, Insulation Resistance 1000m, Withstand voltage: No breakdown or flashover, Appearance: No damage	One cycle: -553C 30min, room temp 10-15min; 853C 30min, room temp 10-15min. Total cycle: 5 cycles.
Salt Spray	Contact Resistance 40m, Appearance: No damage	Temperature: 353 C, Concentration: 51%, Period: Stamping before tin plated for 24 hours or Stamping after tin plated for 8 hours
Solder ability	Soldering area: 90 %	Solder temperature: 2455C, Immersion period: 3 0.5S
Resistance to soldering heat	Appearance: No damage	Manual soldering: Soldering temperature: 350 5 , Soldering time: 3 0.5S; Wave soldering: Soldering temperature: 260 5 C, Soldering time: 5 0.5S