2.00mm Pitch Double Row Connector HCTL HC-PH-2Y-L-05 Electrical Component with Tin Plated Contacts

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification covers the 2.00mm pitch PH connector, double row type. It details product performance, test methods, and inspection requirements for electrical and mechanical applications.

Product Attributes

Brand: HCTLDZ ()
Origin: Shenzhen, China
Material (Housing): Nylon66 UL94V-0
Material (Contact): Brass (Tin plating: 2.5-5m) or Phosphor bronze (Tin plating: 2-4m)
Color (Housing): White
Certifications: ROHS

Technical Specifications

Item	Requirement	Test Mode
General Principles
Scope	This specification applies to the 2.0 series connector strip, including product performance, test methods and test requirements.
Applicable Standards	GB/T2421, GB/T2423, GB/T2424, GB/T5095
Appearance	Product surface without defect, dirt, crack, and mechanical damage; contact parts without rust, plating oxidation, peeling, etc.
Exchangeability	Products of the same specification should be interchangeable.
Use Condition
Ambient Temperature	-25 +85
Applicable Wire Sizes	AWG #24#30
Applicable PC Board Thickness	0.81.6mm
Electrical Performance
Rated Voltage	100V AC/DC
Rated Current	2A AC/DC
Withstand Voltage	No breakdown or flashover	Apply 800V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors
Contact Resistance	20m (Initial value)	Apply a maximum voltage of 20mV and maximum current of 100mA to the mate connector. Does not include wire resistance.
Insulation Resistance	1000 M	Apply 1000V DC (rms) for 1 minute between adjacent contacts to measure the insulation resistance.
Mechanical Performance
Terminal Crimping Wire Strength	30N (AWG#24), 20N (AWG#26), 13N (AWG#28), 8N (AWG#30)	Axial pullout force at a rate of 25 3mm per minute.
Fixed Terminals and Hole Seat	12N	The terminal and the hole seat are pulled out from the hole in the seat capacity at a rate of 25 3mm per minute along the wire direction.
Single Contact Withdrawal Force	2N	Single contact withdrawal force.
Fixed Pin Force	12N	Force is applied to the pin end at a rate of 25 3mm per minute until the needle exits the seat.
Single Contact Insertion Force	10N	Housing together with terminal ends with wafer matched at a rate of 25 3mm per minute inserting force test.
Durability	Contact Resistance 40m; Appearance: No damage	Mate connectors up to 30 cycles at a maximum rate of 10 cycles per minute prior to environmental test.
Vibration	Contact Resistance 40m; Current Discontinuity: Max 1 micro second	Mate connector combination state on the welding circuit board as test samples, subjected to vibration test. Amplitude: 1.5mm p-p; Frequency: 10-55-10Hz/minute; Duration: 2 hours for each direction (X, Y, Z axes).
Environmental Performance
Thermal Aging	Contact Resistance 40m; Appearance: No damage	Connector combination placed in a heating oven at 852 for 96 hours continuously.
Temperature Rise	Measure contact temperature rise when maximum rated current is passed.
Constant Humidity	Contact Resistance 40m; Insulation Resistance 1000m; Appearance: No damage	Connector combination placed in a constant temperature and humidity chamber at 402 and 90-95% RH for 96 hours continuously.
Temperature Cycling	Appearance: No damage; Withstand Voltage: No breakdown or flashover	One cycle: -553 for 30min, then room temp for 10-15min; followed by 853 for 30min, then room temp for 10-15min. Total 5 cycles.
Salt Spray	Contact Resistance 40m; Appearance: No damage	Test samples placed in a salt spray chamber at 353 with 51% salt solution. Stamping after tin plated for 8 hours or Stamping before tin plated for 24 hours.
Solder Ability	Soldering Area: 90%	Soldering temperature: 2455; Immersion period: 3 0.5S.
Resistance to Soldering Heat	Appearance: No damage	Wave soldering: 2605 for 50.5S. Hand soldering: 3505 for 30.5S. Solder position: 1.5mm for DIP type, 0.5mm for SMT type from conductor/fixed piece end.