Hot Rolled Stainless Steel Rebar
Hot Rolled 316L /304 Stainless Steel Rebar Bar Thread Deformed Steel Rebar Reinforcing Steel Rebar for Building
What are Stainless Steel Reinforcing bars?
Stainless steel reinforcing bars are low carbon steel alloy bars and contains minimum 12% of chromium and 8 to 12% of nickel in it. Stainless steel bars are highly corrosive resistant and they can be cast, pressed and machined.
Types of Stainless Steel Reinforcing Bars
Based on the microstructure, stainless steels can be divided into four types which are:
- Martensitic Stainless Steel
- Ferritic Stainless Steel
- Austenitic Stainless Steel
- Austenitic-Ferritic or Duplex Stainless Steel
| Rebars(Hot Rolled Deformed Steel Bar And Wire Rod) | |
| Products | Stainless Steel Deformed steel bar |
| Diameter | 8-25mm |
| Grade | 304 |
| Length | 6M 12M,Customers' Requirement |
| Application | Building/construction |
| Packing | Standard export packing or as customers required |
| Hot-rolled & ribbed steel bars for ferroconcrete (wire rod/bars) | |
| Diameter | 5mm/5.5mm/6mm/6.5mm-19mm |
| Grade | 304 1.4301 |
| Length | About 2 tons per coil |
| Application | Building/construction |
| Packing | Standard export packing or as customers required |
| Material | 304 1.4301 |
| Rebar | |
| Diameter(mm) | Theoretical weight(kg/m) |
| 6 | 0.2221 |
| 8 | 0.3949 |
| 10 | 0.6170 |
| 12 | 0.8885 |
| 14 | 1.2093 |
| 16 | 1.5795 |
| 18 | 1.9991 |
| 20 | 2.4680 |
| 22 | 2.9863 |
| 25 | 3.8563 |
| 28 | 4.8373 |
| 32 | 6.3181 |
| 36 | 7.9963 |
| 40 | 9.8720 |
Austenitic Stainless steels are classified into different grades in different countries based on the proportions of main elements. Which are as follows
Table 1: Classification of Austenitic Steel according to International Standards
| Steel Type | Europe | USA | Britain | Sweden | |
| EN 10088-1 (DIN) | France | AISI | BS | SS | |
| Austenitic | 1.4301 | X5CrNi 18-10 | 304 | 314S11/314S15 | 2332 |
| 1.4401 | X5CrNiMo 17-12-2 | 316 | 316S33 | 2347 | |
| 1.4429 | X2CrNiMoN 17-13-3 | 316LN | 316S63 | 2375 | |
| 1.4436 | X5CrNiMo 17-12-2 | 316 | - | 2343 | |
| 1.4571 | X6CrNiMoTi 17-12-2 | 316Ti | - | 2350 | |
- X – High alloy of steel
- A number after X represents the 100 times the carbon content.
- Cr, Ni, Mo, N and Ti represents Chromium, nickel, Molybdenum, nitrogen and Titanium and the numbers below them represents the composition of elements in percentages.
- For example if we take austenitic steel of designation “X5CrNi (18-10)” , It is the high alloy steel of 0.05% carbon, 18% of chromium and 10% nickel.
2. Austenitic-Ferritic or Duplex Stainless Steel
Austenitic-Ferritic steel has combined properties of austenitic and ferritic stainless steel hence it is also called as duplex stainless steel. It contains less amount of nickel than austenitic. It provides good strength as well as ductility.
Fig 3: Stainless Steel Bars of Different Sizes
It is very good resistant against corrosion. Duplex steels are widely used in paper, pulp, petrochemical industries etc. Duplex steel are also classified according proportion of main elements with different grade in different countries.
Table 2: Classification of Duplex Steel according to International Standards
| Steel Type | Europe | USA | Britain | Sweden | |
| EN 10088-1 (DIN) | France | AISI | BS | SS | |
| Ferritic – Austenitic (lean duplex type | 1.4362 | X2CrNiMo 23-4 | 2304 | - | - |
| Ferritic – Austenitic (duplex type) | 1.4462 | X2CrNiMoN 22-5-3 | 2205 | 318 | 2377 |
Composition of Stainless Steel Reinforcing Bars
Stainless steel bars majorly contain chromium and nickel as the second major compound. They also contain some other elements like molybdenum, nitrogen and very less amount of carbon. Composition of different grades of stainless steels is expressed in below table. The grades specified by AISI are taken into consideration.
Table 3: Composition of Stainless Steel Types
| Type of Steel | Grade (AISI) | Chromium (%) | Nickel (%) | Molybdenum (%) | Nitrogen (%) | Carbon (%)(max) |
| Austenitic | 304 | 18 | 8 | 0.08 | ||
| 316 | 17 | 12 | 2.5 | 0.08 | ||
| 316LN | 17 | 12 | 2.5 | 0.13 | 0.03 | |
| Duplex | 2304 | 23 | 4 | 0.3 | 0.1 | 0.03 |
| 2205 | 22 | 5 | 3 | 0.14 | 0.03 |
Functions of Ingredients of Stainless Steel Bars
Chromium, the major element of stainless steel gives protection against corrosion by forming an oxide film on the steel surface. This film is adherent, rough and invisible. Whenever the bar is attacked chemically this film prevents the bar by releasing small amounts of oxygen. Increase in chromium content will increase the chances of formation of oxide film under critical conditions. Nickel improves the properties like ductility and formability of stainless steel. Other elements like Molybdenum, nitrogen are also improves the corrosion resistance along with chromium.
Fig 4: Stainless Steel Reinforcement for Foundation
Properties of Stainless Steel Reinforcing Bars
The Properties of stainless Steel reinforcing Bars are
- Corrosion Resistance
- High Strength
- Higher ductility
- Cryogenic Resistance
- Fire Resistance
- Magnetic Response
1.Corrosion Resistance
The main property of stainless steel is the corrosion resistance. As explained earlier the corrosion resistance is obtained by the oxide layer formed by chromium content of steel.
2. High Strength
The tensile strength stainless steel bars is much more than mild steel bars. In stainless steels, duplex steel bars are stronger in tension than austenitic steel bars.
3. Higher ductility
Ductility of stainless steel is due to nickel content. Higher the nickel content higher the ductility. Austenitic steel has more ductility than duplex steel.
4. Cryogenic Resistance
At low temperatures, Austenitic Stainless steel bars have high tensile strength with excellent toughness. Other types like martensitic and ferritic are not suitable in cryogenic areas.
5. Fire Resistance
Steel generally has good fire resistance and when it comes to stainless steel, even at high temperatures it cannot lost its strength.
6. Magnetic Response
Except austenitic steel, all other types are able to attract to the magnet. Higher quantity of nickel eliminates the magnetic response of stainless steel.
Table 4: Comparison of Properties of Austenitic and Duplex Stainless Steels
| Property | Type of Stainless Steel | |
| Austenitic | Duplex | |
| Yield Strength (Mpa) | 205 -500 | 330-560 |
| Tensile Strength (Mpa) | 550-860 | 570-1000 |
| Elongation percentage | 30-60 | 25-40 |
| Magnetic | No | Yes |
Products:
Stainless Steel Plate
Stainless Steel Coil
Stainless Steel Strip
Stainless Steel Bar
Stainless Steel Pipe
Stainless Steel Pipe Fittings
Stainless Steel Flange
Available in various sizes, dimensions, shapes and Custom size and shape available !
Materials includes:
Stainless Steel / Duplex & Super Duplex Stainless Steel / Super Ferritics & Ferritics / Nickel Alloys / Copper Alloys / Titanium etc.
Applications :
Oil & Gas / Power Generation / Chemical / Petrochemical / Food & Dairy / Beverage / General Commercial / Shipbuilding etc.
Exported Markets:
USA /Brazil / Spain / German / Isreal / Azerbaijan / Mexico / Chile / Costa Rica / Argentina / / Venezuela / Thailand / Indonesia / Singapore / Malaysia/Vietnam /Ziwbabwe /Qatar/Kuwait /United Arab Emirates , Kingdom of Saudi Arabia /Jordan/Iran/ Pakistan /etc.
Mission:
Our mission is build our reputation by supplying high quality products with unparalleled reliability and guaranteed performance. We are committed to providing you with the best solutions to become your trusted partners in your business and life.
Company Values:
1. Innovation
2. Commitment to Excellence
3. Listening & Respect
4. Team Work
1.What's your advantage?
A: Competitive price and delivery on time , large quantity in stock ,we can make sure very fast shipment out
2. How I believe you?
A : Visit us office or factory, or 3rd part inspection the goods before shipment
3.Can you give warranty of your products?
A: Yes .All products quality warranty more than 12 month
4. Can I visit you?
A: Sure,welcome to visit us at any time.
5.How about the delivery time?
A: plates and coils usually 3-7 days , the strip usually 15 days , the pipe usually 15 days for welded pipe , and 30 days for the seamless pipe , pipe fittings usually 15-20 days , the flanges usually 15 days
6.what kind of payment does your company support?
A: T/T, 100% L/C at sight, Cash, Western Union are all accepted
7. Do you have sample and sample free ?
A: Yes , we have many samples in hand and one sample is free for you
8. Do you have ISO 9001-2008 certificate ?
A : Yes , we have
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.