NAT Hardware Acceleration 20Gbps Gigabit Wired Router UBNT ER-10X

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Brand: UBNT

Product Description

UBNT Gigabit wired router ER-10X 10-port carrier-grade NAT hardware acceleration

Installation Requirements

Wall-mounting (optional)
- Drill with 6 mm drill bit
- Phillips screwdriver
For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti.

System LED
Flashing White	Bootup in Progress
White	Ready for Use Not Connected to Ubiquiti® Network Management System (UNMS™)
Blue	Ready for Use Connected to UNMS
Steady Blue with Occasional Flashing	Ready for Use Unable to Connect to UNMS
Quickly Flashing Blue	Used to Locate a Device in UNMS
Alternating Blue/White	Firmware Upgrade in Progress
RJ45 Speed/Link/Activity LED (Ports 1 - 8)
Off	No Link
Amber	Link Established at 10/100 Mbps Flashing Indicates Activity
Green	Link Established at 1000 Mbps Flashing Indicates Activity
SFP Link/Activity LED (Ports 9 - 10)
Off	No Link
Green	Link Established at 1 Gbps Flashing Indicates Activity
RJ45 (Ports 1 - 8)
RJ45 ports support 10/100/1000 Ethernet connections. PoE In (Port 1) Supports 24V Passive PoE input. PoE Out (Port 8) Supports 24V Passive PoE passthrough.
SFP (Ports 9 - 10)
Hot-swappable SFP ports support 1 Gbps connections. If you use a copper Ethernet module (example: UF-RJ45-1G), power off the EdgeSwitch before insertion; otherwise there may be a device reboot.
Reset Button
To reset to factory defaults: Disconnect power from the EdgeSwitch. Reconnect power while holding the Reset button. The port LEDs will light up in sequential order (this takes approximately five seconds). When the port 1 LED flashes again, release the Reset button.
Power
Connect the included Power Adapter to the Power port.
Grounding Point
Ground bonding point for an optional ground wire.

ES-10X
Dimensions	207 x 31.1 x 90 mm (8.15 x 1.22 x 3.54")
Weight	500 g (1.10 lb)
Total Non-Blocking Throughput	10 Gbps
Switching Capacity	20 Gbps
Forwarding Rate	14.88 Mpps
Max. Power Consumption (Excluding PoE Output)	8W
Power Method	24VDC, 1A or 24V Passive PoE
Supported Voltage Range	9 -30VDC
Power Supply	24VDC, 1A Power Adapter (Included) or 24V Passive PoE
LEDs
System	Status
RJ45 Data Ports	Link/Speed/Activity
SFP Data Ports	Link/Activity
Networking Interfaces	(8) 10/100/1000 Mbps RJ45 Ports (2) 1 Gbps SFP Ports
Management Interface	Ethernet In-Band
Certifications	CE, FCC, IC
ESD/EMP Protection	Air: ± 24 kV, Contact: ± 24 kV
Operating Temperature	-10 to 50° C (14 to 122° F)
Operating Humidity	5 to 95% Noncondensing
Shock and Vibration	ETSI300-019-1.4 Standard