Installation Requirements
- Wall-mounting (optional)
- Drill with 6 mm drill bit
- Phillips screwdriver
- For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
- For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti.
-
System LED
Flashing White Bootup in Progress White Ready for Use
Not Connected to Ubiquiti® Network Management System (UNMS™)
Blue Ready for Use
Connected to UNMS
Steady Blue with Occasional Flashing Ready for Use
Unable to Connect to UNMS
Quickly Flashing Blue Used to Locate a Device in UNMS Alternating Blue/White Firmware Upgrade in Progress RJ45 PoE LED (Ports 1 - 8)
Off No Power over Ethernet Green 24V Power over Ethernet RJ45 Speed/Link/Activity LED (Ports 1 - 8)
Off No Link Amber Link Established at 10/100 Mbps
Flashing Indicates Activity
Green Link Established at 1000 Mbps
Flashing Indicates Activity
SFP Link/Activity LED (Ports 9 - 10)
Off No Link Green Link Established at 1 Gbps
Flashing Indicates Activity
RJ45 (Ports 1 - 8)
RJ45 ports support 10/100/1000 Ethernet connections and 24V Passive Power over Ethernet (PoE) output. SFP (Ports 9 - 10)
Hot-swappable SFP ports support 1 Gbps connections. If you use a copper Ethernet module (example: UF-RJ45-1G), power off the EdgeSwitch before insertion; otherwise there may be a device reboot. Reset Button
To reset to factory defaults:
- Disconnect power from the EdgeSwitch.
- Reconnect power while holding the Reset button. The port LEDs will light up in sequential order (this takes approximately five seconds).
- When the port 1 LED flashes again, release the Reset button.
Power
Connect the included Power Adapter to the Power port. Grounding Point
Ground bonding point for an optional ground wire.
Specifications
| ES-10XP | |
|
Dimensions |
207 x 31.1 x 90 mm (8.15 x 1.22 x 3.54") |
|---|---|
|
Weight |
500 g (1.10 lb) |
|
Total Non-Blocking Throughput |
10 Gbps |
|
Switching Capacity |
20 Gbps |
|
Forwarding Rate |
14.88 Mpps |
|
Max. Power Consumption |
8W |
|
Power Method |
24VDC, 2.5A |
|
Supported Voltage Range |
9 - 30VDC, 5A |
|
Power Supply |
24VDC, 2.5A Power Adapter (Included) |
|
LEDs |
|
| System | Status |
| RJ45 Data Ports | PoE, Link/Speed/Activity |
| SFP Data Ports | Link/Activity |
|
Networking Interfaces |
(8) 10/100/1000 Mbps RJ45 Ports (2) 1 Gbps SFP Ports |
|
Management Interface |
Ethernet In-Band |
|
Certifications |
CE, FCC, IC |
|
ESD/EMP Protection |
Air: ± 24 kV, Contact: ± 24 kV |
|
Operating Temperature |
-10 to 50° C (14 to 122° F) |
|
Operating Humidity |
5 to 95% Noncondensing |
|
Shock and Vibration |
ETSI300-019-1.4 Standard |
| PoE | |
|
PoE Interface |
(8) 24VDC Passive PoE (Pins 4, 5+; 7, 8-) |
|---|---|
|
Max. Passive PoE Wattage per Port |
15W |
|
24V Passive PoE Voltage Range |
24V |
