FEMDNN032G-A3A55 EMMC Memory Chip
- eMMC5.1 specification compatibility(Backward compatible to eMMC4.41/4.5/5.0)
- Bus mode
- Data bus width: 1 bit (default), 4 bits, 8 bits
- Data transfer rate: up to 400MB/s (HS400)
- MMC I/F Clock frequency : 0~200MHz
- Operating voltage range
- Vcc(NAND) : 2.7 - 3.6V
- Vccq(Controller) : 1.7 - 1.95V / 2.7 - 3.6V
- Temperature
- Operation (-25℃ ~ +85℃)
- Storage without operation (-40℃ ~ +85℃)
- Sudden-Power-Loss safeguard
- Hardware ECC engine
- Unique firmware backup mechanism
- Global-wear-leveling
- Supported features.
- HS400, HS200
- Partitioning, RPMB
- Boot feature, boot partition
- HW Reset/SW Reset
- Discard, Trim, Erase, Sanitize
- Background operations, HPI
- Enhanced reliable write
- S.M.A.R.T. Health Report
- FFU
- Sleep / awake
- Others
- Compliance with the RoHS Directive
FORESEE eMMC with powerful L2P (Logical to Physical) NAND Flash management algorithm provides unique functions:
- Host independence from details of operating NAND flash
- Internal ECC to correct defect in NAND flash
- Sudden-Power-Loss safeguard
To prevent from data loss, a mechanism named Sudden-Power-Loss safeguard is added in the eMMC. In the case of suddenpower-failure, the eMMC would work properly after power cycling. - Global-wear-leveling
To achieve the best stability and device endurance, this eMMC equips the Global Wear Leveling algorithm. It ensures that not only normal area, but also the frequently accessed area, such as FAT, would be programmed and erased evenly. - IDA(Initial Data Acceleration)
The eMMC prevents the pre-burned data from data-loss with IDA, in case of our customer had pre-burned data to eMMC, before the eMMC being SMT. - Cache
The eMMC enhanced the data written performance with Cache, with which our customer would get more endurance and reliability
The embedded device offers also the possibility of configuring by the host additional split local memory partitions with independent addressable space starting from logical address 0x00000000 for different usage models. Default size of each Boot Area Partition is 4096 KB and can be changed by Vendor Command as multiple of 128KB. Boot area partition size is calculated as ( 128KB * BOOT_SIZE_MULTI ) The size of Boot Area Partition 1 and 2 cannot be set independently and is set as same value Boot area partition which is enhanced partition. Therefore memory block area scan is classified as follows:
- Factory configuration supplies boot partitions.
- The RPMB partition is 16MB.
- The host is free to configure one segment in the User Data Area to be implemented as enhanced storage media, and to specify its starting location and size in terms of Write Protect Groups. The attributes of this Enhanced User Data Area can be programmed only once during the device life-cycle (one-time programmable).
- Up to four General Purpose Area Partitions can be configured to store user data or sensitive data, or for other host usage models. The size of these partitions is a multiple of the write protect group. Size and attributes can be programmed once in device life-cycle (one-time programmable). Each of the General Purpose Area Partitions can be implemented with enhanced technological features
Each cycle of the clock directs a transfer on the command line and on the data lines.
This signal is a bidirectional command channel used for device initialization and command transfer. The CMD Signal has 2 operation modes: open drain, for initialization, and push-pull, for command transfer. Commands are sent from the host to the device, and responses are sent from the device to the host.
These are bidirectional data signal. The DAT signals operate in push-pull mode. By default, after power-up or RESET, only DAT0 is used for data transfer. The controller can configure a wider data bus for data transfer wither using DAT [3:0](4bit mode)or DAT[7:0](8bit mode). Includes internal pull-up resistors for data lines DAT[7:1]. Immediately after entering the 4-bit mode,the device disconnects the internal pull-up resistors on the DAT1 and DAT2 lines.(The DAT3 line internal pull-up is left connected.) Upon entering the 8bit mode, the device disconnects the internal pull-up on the DAT1, DAT2, and DAT[7:4]lines.
Newly assigned pin for HS400 mode. Data Strobe is generated from e.MMC to host. In HS400 mode, read data and CRC response are synchronized with Data Strobe.
Hardware Reset Input
Vccq is the power supply line for host interface, have two power mode: High power mode:2.7V~3.6V
Standard export packaging available. Customers can choose from cartons, wooden cases, and wooden pallets according to their requirements.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.