Controller Board for Arduino

Specifications: This development board with a PIC16F877A chip. The DIP40 locking device, easy to remove the PIC microcontroller for reuse 8 independent LED(Marquee experiments) 4 common anode digital tube 1 * 4 independent keys 4 * 4 matrix of buttons DS1302 Electronic Clock (electronic clock experiment) DS18B20 temperature sensor (temperature detection and display) AT24C02 I2C external memory internal EEPROM read

Electronic Project 4 DC Motor Driver Module L293D Module Sheild For Arduino Introductions The drive module can directly drive four DC motors, drive the car chassis is 4WD 4 choice. Driving battery big up to 1A generally smart car motor current 100-300MA only four are sufficient to meet the control requirements. While leaving Road stepper motor interface can drive Road five line four-phase stepper motor or Road, two-phase four-wire stepper motor, very suitable for precise

Description The Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a

Red Game Joystick Shield V1.A Expansion Board For Electronic Robotics Project Description The Joystick Shield connects directly on an UNO, Leonardo or MEGA type plate and allows to have a control plate quickly and without complications. The joystick is analog and is directly connected to the analog inputs of the Arduino, in addition you can press to add another function. The board also has 4 buttons with bezel connected to the digital pins. It is delivered assembled with the

Description: The Uno board Clone is a microcontroller board based on the ATmega328. It has 14 digital input/outputpins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USBconnection, a power jack, an ICSP header, and a reset button. It contains everything needed to support themicrocontroller; simply connect it to a computer with a USB cable or power it with a AC

0.96" OLED STM32 Smart Core STM32F103 STM32F103C8T6 ARM Cortex M3 32 Discovery Product Description ARM Cortex M3 @ 72MHz 20k RAM 32khz RTC crystal JTAG / ST-Link connector 8-pin 0.96" OLED SWD header 2 rows of 20 pins for GPIO etc Unpopulated 6-pin 3.3V, 5V, and GND header EEPROM Compatible with Ard development environment (must flash the bootloader) - search for "STM32 Smart stm32duino" Please consider taking advantage of our multi-item discount found at the top of the

IO Sensor Shield V1 14 Digital Interfaces SD card Expansion Interface 3.3V Power Product Feature Fully compatible with UNO R3 interface New color row of needle seat, yellow for the digital mouth, blue for the analog port, red for the power interface, easy to identify All 3P interfaces are compatible with 3P DuPont sensor cable colors to prevent insertion errors All gold-plated pins, materials used sophisticated, electrical performance and stability Excellent PCB design,

WiFi CP2102 development board for NodeMCU ESP8266 Board with 0.96 OLED Product Description This is a low cost A’board-compatible ESP8266 development board. A 0.96″” OLED display is on the board. It is very easy for beginners. You can program it like A’board. There is a project support for ESP8266 chip to the A’board environment: A’board core for ESP8266 WiFi chip. Another famous project is NodeMCU, which you can use LUA to control ESP8266. Features All ESP8266 pins broken out

Development Board 50*50mm Quad Band SIM808 5V - 20v SMS GSM GPRS GPS Module Specifications: Voltage Range 5-18V Lithium Battery Interface Voltage 3.4-4.4V Operating Temperature -40-+85℃ Storage Temperature -45to+90℃ Size 50*50mm GSM/GPRS Characteristic Bands: GSM 850,EGSM900,DCS 1800,PCS 1900 Transmit Power Class 4(2W)at GSM 850 and EGSM 900 Class 1(1W)at DCS 1800 and PCS 1900 GPRS Transmission Rate GPRS Downlink Data Transmission:max.85.6kbps GPRS Uplink Data Transmission:

Sim900a Wireless Data Transmission Module GSM GPRS Board Kit With Ante Product Description 1. Support 2, mobile phone 3, 4G card. 2. The onboard two set power supply interface VCC5 5V power supply, VCC4 interface, 3.5--4.5V power supply, optional power on self starting (default) and control start. 3. The onboard SMA (default) and IPXmini antenna interface, SIM900A interface reserved reset. 4. The computer can give early computer debugging USB module power supply, a very large

Mini USB Nano V3.0 ATMEGA328P-AU 16M 5V Micro-controller Nano V3 Board Quick Detail: Nano is an ultra-small Simple I/O platform base with open source code .Compared with the previous USB version Diecimila , Nano has a large advantage in size.It can be used to develop electronic appliances which run independently and the interactive effects;Can also be used to develop interactive work which connect to a computer and work with same Flash, Processing, Max/Msp, PD, VVVV software

Mega 2560 UNO R3 Motor Drive Motor Shield Expansion Board L293D Description: Here we have a L293D monolithic integrated, high voltage, high current, 4-channel driver. You can use DC motors and power supplies of up to 36 Volts, thats some pretty big motors and the chip can supply a maximum current of 600mA per channel. The L293D chip is also what’s known as a type of H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in

Product Specifiction: Mini breadboard size 4.4cm x 3.4cm x 1cm Breadboard type 170 tie points Prototype Size 7cm x 5.5cm x 2cm Function the circuit prototype Detail 1 reset button, 1 general use button, and 2 LED circuits Weight(including the mini breadboard) 33g Pack Size 10cm*10cm*5cm Product Feature: power busses for +5V and GND in middle of board central bus can be configured to carry +5V, GND,

New ATMEGA328P-AU nano V3.0 R3 Board ( Original chip )With USB Cable Product Introduction: The Funduino Nano V3 development board is with the open original design schematics, free software interface, and also according to the needs and modifies the download process is simple and convenient. the development of the user interface and the environment is very simple, easy to understand, very suitable for beginners to learn. Product Details: 1) 12 digital input/output ports,D2-D13

Original New DUE R3 Board SAM3X8E 32-bit ARM Cortex-M3 Control Board Product Introduction: The Arduino Due is the newcomer microcontroller board in the Arduino boards family. It's the first board based on a 32 bit ARM core processor, the AtmelSAM3X8E ARM Cortex-M3 MCU, that improve all the standard Arduino functionalities and add more new features. It offer 54 digital input/output pins (of which 12 can be used as PWM outputs, with selectable resolution), 12 analog inputs with

UNO r3 Leonardo atmega328p with Controller ATMEGA32U4 Development Board Module Product Introduction: Leonardo is the team's latest low-cost controller. It has 20 digital inputs and outputs, 7 PWM ports and 12 analog inputs. Compared to other versions of the use of independent USB-Serial conversion chip, Leonardo innovative use of a single-chip solution. Only a piece of Atmega32u4 to achieve USB communication and control. This innovative design reduces the cost of Leonardo.

2014 UNO R3 Development Board Improved Version CH340G with USB Cable Product Introduction: The Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with

Original 2014 MICRO USB UNO R3 ATmega328P-AU For Electronic Control Board Product Details: Recommended Input Voltage: 7-12V Min-Max Input Voltage: 6-20V Digital I/O Pins: 54 (of which 12 provide PWM output) Analog Input Pins: 12 Analog Outputs Pins: 2 Total DC Output Current on all I/O lines: 130 mA DC Current for 3.3V Pin: 800 mA DC Current for 5V Pin: 2A Flash Memory: 512 KB all available for the user applications SRAM: 96 KB (two banks: 64KB and 32KB) Clock Speed: 84 MHz 1

Original Electronic Module UNO R3 ATmega328P ATmega16U2 with USB Cable UNO R3 Product introduction: 1. Open circuit diagram of the original design, the development of software interface for free download, can also be in accordance with the requirements and their modified, download the program is simple and convenient. Can simply use sensors, all kinds of electronic components connection (such as: LED lights, buzzer, buttons, photoresistance, etc.), make all sorts of

Description: L298P Shield DC motor drives using LGS's outstanding high-power motor driver chip dedicated L298P, can directly drive two DC motors, drive current up to 2A, motor output using eight-speed Schottky diodes as protection. Stack design can be directly plugged for Arduino, easier to use! Specifications: Logical part of the input voltage VD: 5V Driven part of the input voltage VS: VIN