Shield for Arduino

Description: The latest version adds section micro-SD card slot, with a network storage capabilities. In addition, it and the Arduino Duemilanove, Mega series is also fully compatible. It also has a separate PoE (power-over-Ethernet) modules. The module can be soldered to the motherboard, which is transmitted via twisted pair electricity. It is compliant with IEEE802.3af standard, and is compatible with

Description: The shield uses WizFi210 which is a low power-consuming WIFI module which is applied with dynamic power management technology. When the WIFI module needs to be on but not work, it can be set to standby mode a low power mode, and the module just needs to be woken up when it has to work. The WIFI wireless module is based on WizFi210. It provides the bridging from TTL serial port communication to

Quick Detail: - Wifi Chip: WizFi210; - Radio Protocol: IEEE 802.11b/g/n Compatible; - Supported Data Rates: 11, 5.5, 2, 1 Mbps (IEEE 802.11b); - Modulation: DSSS and CCK; - RF Operating Frequency: 2.4 - 2.497 GHz; - Antenna Options: Chip antenna and U.FL connector for external antenna; - Networking Protocols: UDP, TCP/IP (IPv4), DHCP, ARP, DNS, HTTP/HTTPS Description: The shield uses WizFi210 which is

WiFi shields V2.1 low-power wireless WiFi Module For Arduino , Shield For Arduino Quick Detail: 1. Operating Voltage: 5V DC. 2.Input Voltage (recommended): 7-12V DC. 3. Input Voltage (limits): 6-20V DC. 4. Buckled Analog Port : Handy, solid connection to 6 Analog inputs with VCC/GND. 5. Digital IO port : 13 ports prepared to digital modules or servos. 6. Analog IO Port: 2.54 grid male pin header connections. Description: The shield uses WizFi210 which is a low power-consuming

Description: - Support SD card module communication interface - Support APC220 wireless rf modules communication interface - Support RB URF ultrasonic sensors interface - Support LCD serial and parallel interface - Support Kinds of interface and can be fully compatibled with Ardu Mega - Emartee Mega Sensor Shield V1.0 pinout all of the digital and analog interface: - Support IIC interface - Support 32

Description: Support interface: IIC interface. 32 road Servo Motor Drive Shield interface. bluetooth module communication interface. SD card module communication interface. APC220 wireless rf modules communication interface. RB URF ultrasonic sensors interface. LCD serial and parallel interface. Kinds of interface and can be fully compatibled with Mega 32 road Servo Motor Drive Shield interface for Arduino. New MEGA Sensor shields

Sensor Shield For Arduino Digital Analog Module Servos , Sensor Shield V1.0 Description: - Emartee Mega Sensor Shield V1.0 pinout all of the digital and analog interface: - Support IIC interface - Support 32 road Servo Motor Drive Shield interface - Support bluetooth module communication interface - Support SD card module communication interface - Support APC220 wireless rf modules communication interface - Support RB URF ultrasonic sensors interface - Support LCD serial and

MEGA Proto Shield V3 proto type expansion board for mega 2560 Quick Detail: You can plug it directly into an Arduino MEGA with no soldering required. Allows soldering of components directly on to the shield Comes with mini breadboard which can be fixed directly onto the shield allowing for solderless prototyping. Integrated power indicator, status lights and reset button Description: Compatible with Arduino Mega

Quick Detail: 14 I/O Pin (servo type with GND, power and signal) 8 analog Pin with power output and GND 6 PWM Pin 1 Servo power input I2C expansion Pin AREF output 3.3V output Description: 1. expand all digital IO and analog IO interface. all of them have + and - pole for power input 2. expand I2C interface 3. expand DC power interface for NANO USB interface Competitive Advantage: 1.Convenient & Friendly Customer

Quick Detail: 1. extension of 14 digital IO ports (12 servo interface) and power; 2. six analog IO ports and power; 3. one digital external power port terminal; 4. Digital-port external power supply and an onboard power supply automatic switching; 5. one External power input terminal and an input pin; Description: 1.extension of 14 digital IO ports (12 servo interface) and power; 2. six analog IO

Description: 1.DIY PCB Universal Board 2.Arduino UNO board 3.PIC Programming unit 4.AVR ATMEL Programming unit 5.Connector Kit 6.USB to TLL Modules 7.Power Modules 8.LCD Modules 9.RS232 TO TLL Moudle Specifications: Add The nRF24L01 RF interface Add the Nokia 5110 LCD interface, so very convenient for game development Add Bluetooth module interface, convenient Bluetooth wireless serial communication Add

Quick Detail: 1. Operating Voltage: 5V DC. 2.Input Voltage (recommended): 7-12V DC. 3. Input Voltage (limits): 6-20V DC. 4. Buckled Analog Port : Handy, solid connection to 6 Analog inputs with VCC/GND. 5. Digital IO port : 13 ports prepared to digital modules or servos. 6. Analog IO Port: 2.54 grid male pin header connections. Description: Perfect High Quality New Arduino Sensor Shield Digital Analog Module Servos V4 Brand new and high

Description: L293D is a monolithic integrated, high voltage, high current, 4-channel driver.Basically this means using this chip you can use DC motors and power supplies of up to 36 Volts, thats some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what's known as a type of H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage

Arduino Proto Shield prototype shield with mini bread board Quick Detail: Brand new and high quality. Small soldering area. All Arduino pins are brought to the top level. 1 reset button, 1 general use button, and 2 LED circuits can be used directly. 5V, GND, and Raw pins are exposed as well. SOIC place for IC. The mini breadboard has 170 tie points. The breadboard sticks on the prototype shield with its self-adhesive

Quick Detail: 1. Easy integration with an Arduino with extra long pins to be able to clear the USB jack 2. Adds Internet capability to any Arduino with the standard headers 3. Fully supported by the Arduino ethernet library 4. Provides both a TCP and UDP IP stack Description: The W5100 Ethernet shield fits most Arduino compatible boards with the standard pin headers. This shield allows your Arduino to

Specification: Supported Arduino board Compatible with the Arduino Network (IP) stack capable CP and UDP Weight 30g Model number OKY2101 Other feature Micro SD card slot Chip Wiznet W5100 Ethernet Chip Keyword W5100 Color blue FAQ 1. What is the terms of payment? L/C,D/A,D/P,T/T,Western Union,MoneyGram 2. What is the delivery time? Normally, 1-5 workdays after payment; Special requirement orders,

​ Specifications: Operating Voltage 3-5.5V Output 9 ~ 12 adjustable resolution Temperature measure precision ±0.5°C Testing Temprature ,-55 ~ +125Degrees Size Stainless steel shell (6 * 50 mm), wire length 100 cm Output pin Red (VCC), yellow (DATA), black (GND) Weight 25g Keyword DS18B20 Condition New Description: Pluggable terminal waterproof DS18B20 temperature sensor can be used in many places, such as soil temperature detection, hot

DS18b20 Digital Temperature Sensor Module Or Single-Bus Digital Temperature Sensor Specifications: Operating Voltage 3.3-5V Output digital signal output Temperature measure precision 0.5℃ Testing Temprature -55 ~ +125℃ Size 30mm*15 mm*10mm Weight 4g Color blue Keyword DS18b20 Type Temperature Sensor Module Condition New FAQ 1. What is the terms of payment? L/C,D/A,D/P,T/T,Western Union,MoneyGram 2. What is the delivery time? Normally, 1-5 workdays after payment; Special

Specifications: Origin China Type Voltage Regulator Supply Voltage Other warranty 2Year Weight 25G Pack size 10Cm*10Cm*10Cm Condition New Delivery time 1-3 Days User Students,Engineers Package Anti-static Bag,Can Desigin Package Too Description: For Io Expansion Shield Is Specifically Designed To Facilitate Easy Connection Among Many Other Devices. In Essence, It Expands The Controller To Link Those

Specifications: Temperature measurement range -50 ℃ ~ 110 ℃ Temperature measurement error ± 3 ℃ Resolution 0.1 ℃ Sensor Type NTC (10K / 3435) Operating voltage 1.5V Working current MAX 4UA Operating temperature 0 ℃ ~ 50 ℃ Storage temperature .-10 ℃ ~ 60 ℃ Machine size 4.8cm × 2.8cm × 1.5cm Embedded hole size 4.6cm × 2.7cm Cable length 1M Color black, white