Non Destructive Testing Equipment

Field Indicators Magnetic Field Indicators Gauss Meter Scope Type Measurement range ( Tesla) Accuracy Size(mm) JCZ-5 0-5×10-4 ±10% Φ60×23 JCZ-10 0-10×10-4 JCZ-20 0-20×10-4 JCZ-30 0-30×10-4 JCZ-50 0-50×10-4 This instrument can be used in the ambient of –100C to +500C and relative humidity 80 %. Using method During measurement, it should be placed on the surface of part being testing tightly with the indicated arrow, and moved with two sides direction of the instrument. At the

Magnaflux Pie Field Indicator Overview The Pie Gauge is a tool for quickly verifying the direction of magnetic flux on a surface. It is made from eight ferrous segments, braised into a single piece, providing a star pattern of nonferrous discontinuities. The eight linear discontinuities provide indications in all directions. Typically used with dry powders for yoke inspection, the Pie Gauge can be held at any angle and will generate indications perpendicular to the direction

TG-1000C Online Spheroidization rate Ultrasonic Velocity Gauge Tester TG-1000C is a portable online measurement & command control ultrasonic velocity gauge. Based on the same operating principles as SONAR it is capable of measuring the speed of sound (velocity) through the material. It is suitable for a variety of metallic and non-metallic materials such as casts, alloys or plastics, and can be used to indicate the consistency of the material. Features: High precision timing

HVS-100MDX-AXY Fully Automatic Turret Digital Display Touch Screen Vickers Hardness Tester The HVS-100MDX-AXY fully automatic micro Vickers hardness tester consists of two parts: l THV-100MDX Automatic Turret Digital Display Touch Screen Vickers Hardness Tester l HVS—AXY Vickers hardness automatic measurement and control system HV-100MDX Automatic Turret Digital Display Touch Screen Vickers Hardness Tester Ⅰ, Product Introduction: The HV-100MDX automatic turret digital touch

HVS-1MDT-AXY Automatic Rotating Tower Touch Screen Microscopic Vickers Hardness Tester HVS-1MDT-axy Automatic Microscopic Vickers Hardness Tester consists of two parts: l HV-1MDT automatic rotating tower touch screen micro hardness tester l HVS - AXY Vickers hardness automatic measurement and control system 一, HV-1MDT automatic rotating tower touch screen micro hardness tester Product introduction HV-1MDT automatic turret digital micro hardness tester adopts optical cross

HD-201A/B/C Dial Porosity Holiday Detector 【Function】 HD-201 Porosity Holiday detector is a special testing equipment used to detect oil and gas pipelines, cables, enamel, metal tank, hull and other protective coatings flaws. It is a simple and practical equipment. 【Characteristic】 1,Low power consumption, small size, light weight； 2,Simple operation 【Main technical index】 1,Measuring range: A: 0.03-3.5mm(Epoxy coal tar pitch medium) B: 3.5-10.mm(Petroleum asphalt medium) C:

Sensitivity level determination block ISO 3452-1 Type 1 Test Panel Detection sensitivity: Evaluate whether the penetrant can detect minor defects by detecting star shaped cracks on the test block.Cleanability: By measuring the roughness area on the test block, determine the ease of cleaning the penetrant on the rough surface.Structure and ParametersKit composition: A set of 4 brass plates with electroplating thicknesses of 10 μ m, 20 μ m, 30 μ m, and 50 μ m.Regional division

ISO 3452-3 Type 1 reference block Twin NiCr Sensitivity Panels, NiCr Twin Cracked Penetrant Test Panels ISO 3452-1 Type 1 Test Panel The NiCr Twin Cracked Penetrant Test Panels are used for comparing and evaluating sensitivity and performance of Dye Penetrants. They are available in 10, 20, 30 and 50 microns (0.0004, 0.0008, 0.0012, 0.002 inch) flaw depth. Each set consists of a pair of identical panels marked A and B with manufacturer`s certification and crack photograph.

NDT penetrant comparator block Core purpose·Type 1 reference test block: used to determine the sensitivity level of the penetrant product series (such as whether it belongs to level 1 or level 2 ultra-high risk), mainly used for product rating.·Type 2 reference test block: used to verify the routine performance of fluorescent or dye penetrant detection systems, ensuring the normal testing process. Industry and ApplicationsTypical industries: aerospace, automotive manufacturin

ISO 3452-3 Type 2 reference block Core purpose ·Type 1 reference test block: used to determine the sensitivity level of the penetrant product series (such as whether it belongs to level 1 or level 2 ultra-high risk), mainly used for product rating. ·Type 2 reference test block: used to verify the routine performance of fluorescent or dye penetrant detection systems, ensuring the normal testing process. Type II Penetrate block : ISO 3452-3:2013(E),GB/T18851.3,JIS Z 2343-3

PSM-5 Penetrant System Monitor Panel Calibration Block Penetrant System Monitor Panel,A stainless steel panel, 0.090" thick and measuring 4 x 6 inches. A chrome plated strip runs the length of one side of the panel. Five crack centers are evenly spaced in the chrome plating in order of magnitude; the largest is readily visible with low sensitivity penetrants, while the smallest is difficult to observe even with high sensitivity materials. Adjacent to the chrome plated section

Shim Miniature QQI Standard Flaw Shims for Magnetic Particle Inspection Magnetic QQI Specimens (Quantitative Quality Indicators) are magnetic particle test pieces with artificial defects used to demonstrate field direction and field strength within a part for magnetic particle inspection (MPI) applications. Magnetic QQI's are useful for setting up the magnetization parameters for part-specific MPI techniques. QQI's can be used to create an example part for daily system

MT Inspection Magnetic Yoke Weight Lift Test Bar The Yoke Test Weight is a certified 10 lb / 4.5 kg weight designed specifically for AC magnetic yokes to confirm the yoke has sufficient strength to perform magnetic particle inspections. Each Yoke Test Weight has a built-in leg positioning guide to assure balanced distribution and accurate test results. Use the Yoke Light and Yoke Test Weight to improve your mag particle inspections with Magnaflux HCDX-Y2 and HCDX-Y9

Fluorescent magnetic particle inspection machine 1. Working principle Magnetic particle detection uses the interaction between magnetic leakage field and magnetic powder at the defect of the workpiece. It takes advantage of the difference between the surface and near surface defects of iron and steel products (such as cracks, slag inclusion, hair lines, etc.) permeability and iron and steel permeability. After magnetization, the magnetic field at the discontinuous place of

HD-150 Underground 6 meters Pipe Locator and Pinhole Porosity Detector Application HD-150 pipe locator and porosity detector is easy to operate. The reliability and detecting veracity have been greatly increased. Without dredging up the soil, this instrument can detect conveniently and accurately the position, directions, depth, leaking points. It is one of the most advanced instruments in China. It's the necessity of pipe laying, chemical ect. Technical parameters (1)

HCDX-C280DC DC Demagnetization and Magnetization Particle Inspection Coil I. Product Overview *Product Name: DC Magnetization and Demagnetization Coil *Product Model: HCDX-C280DC *Main Application: This product is a key component of a magnetic particle inspection equipment, used for magnetizing (magnetizing) and demagnetizing iron magnetic workpieces to detect defects on the surface or near the surface of the workpiece. *Product Features: Based on the factory test report,

TG-3400 Big Range 0.65～500mm Ultrasonic Thickness Gauge Application: used for measuring the thickness of hard materials, such as: steel, stainless steel,aluminum, copper, chrome and other metal materials, as well as plastics, rubber, ceramics, glass and other nonmetals. The gauges are widely used in petroleum, chemical industry, electric power, boiler,metallurgy, shipbuilding, aviation, aerospace and other fields. Specifications Measuring Range 0.65 ～ 500mm (45 ＃ Steel) Sound

Viewing Light Density Film with Calibration certificate The core parameters of the film density viewer need to be focused on, including brightness, contrast range, and uniformity. The current mainstream LED film viewer technical parameters are as follows: 1. Key performance indicators 1.1 Relationship between brightness and contrast For blackness ≤ 4.0D Brightness should be ≥ 100,000 cd/m² For blackness ≤ 4.5D Brightness should be ≥ 300,000 cd/m² For blackness ≤ 5.0D

Brinell Hardness Test Block for Standard Calibration The Brinell hardness block is a standard test block used for calibrating Brinell hardness testers. The hardness value (HBW) is calculated by measuring the indentation diameter. The key information is as follows: Core characteristics and parameters Brinell block (180-650)HBW 10/3000 Ф90×Ф12×16 or 60×40×10/ 0.85kg (180-650)HBW 5/750 (180-650)HBW 2.5/187.5 (95-125)HBW 10/1000 (95-125)HBW 5/250 (95-125)HBW 2.5/62.5 1. Test

Bendable Flat Panel Detector for Industrial DR Systems 0410-BA is a new generation, high-performance wireless bendable flat panel detector. It features a 100μm pixel pitch with GOS, and can be bent freely to adapt to the needs of specific work environment, especially as non-destructive tests in the inspection of pipelines. It can improve the quality of image and avoid image distortion. 10 × 25 cm² bendable active area 100μm pixel pitch with 16-bit ADC for more image details