Marine electric equipment
Marine Lighting Marine Flood light
500W Marine Lightings Marine Flood lights IP67 220V 500W/300W tungsten halogen lamp R7s IP67 500W Marine Lightings Marine Flood lights IP67 Application The lamps are suitable for the ships deck.the pier.dock square and other places lighting Characteristic 1.The lamp body is made of stainless steel, 2.Toughened transparent of glass shields, the reflectors is made of high pure aluminum sheet 3.The protection class in IP67. Type Voltage Power Illuminant Luminous flux (lm) Lamp
DNV Certified 25*1.5mm2 Flame Retardant Low Smoke Halogen Free Shipboard Cable
Charateristic: 1 Rated voltage 0.6/1kv 2 Flame-retardant IEC 60332-1-2 and IEC 60332-3-22 3 DA: test for single insulated wire and cable 4 SA: test for bunched wires and cables 5 NA: Fire-resistant 6 SC: Smoke emission Halogen-free 7 NSC: Fire-resistant Smoke emission Halogen-free 8 Maximum Conductor temperature +85 °C Minimum recommended installation temperature -15 °C Lowest operation temperature -40 °C Application: The products above apply for power transmission for
Marine Incandescent Explosion Proof Light
Applied to the ship, petroleum, platform and chemical area which may has gas of inflammable and explosive. Used at the cabin of inflammable material and expolosive gas, such as accumulator room, painting room, lighting room and liquid cargo ship. The environment electric equipment of explosive gas: I: Coal mine electric equipment II: Environment electric equipment of other explosive gas Main Specification: Explosion-proof Mark Exd II CT4 Voltage 220V,24V Power
High Quality EPR Insulated Shipboard Cable Marine Cable
1.EPR/XLPE insulation 2.Naval cable, boat cable, offshore cable 3.Halogen-free fireproof cable EPR Insulated Fire-resisting Shipboard Cable SPECIFICATION & STANDARDS IEC 60288 IEC60092-351 IEC60092-376 IEC60092-359 IEC60332-1 IEC 60331 Construction: 1. Conductor: tinned copper 2. Insulation: EPR 3. Tape 4. Individual screen: tinned copper wire braided 5. Tape 6. Inner sheath: PCP/PO (SHF1, SHF2) 7. Screen/Armored: tinned copper wire braid (Galvanized steel wire braided) 8.
Marine Shipboard Cables And Wires
Marine shipboard cables & wires( JIS C 3410 standards) Rating voltage: 0.6/1kv International Standards applied IEC60228 IEC60092-350 IEC60092-351 IEC60092-353 IEC60092-359 IEC60332-1 IEC60332-3-22 IEC60331 IEC60754-2 IEC60134-2 JIS C 3410 standards JIS C 3002 JIS C 3005 JIS K1433 JIS K 8422 DIN standards DIN89158 DIN89159 DIN89160 Marine cables construction: 1. Conductor: tinned copper wire,class2 or 5 2. Fire resistant Mica tape on request 3. Insulation: XLPE/EPR 4. Filler (
Marine Navigation Signal Light
1.Marine navigation signal light is applied to the ships with the length 50m or above 50m as lamp signal liaison when night navigation . 2.The shell is made of high-strength engineering plastic PA+GF,the lampshade adopts injection of PC,lens hood adopts good quality stainless steel. 3.The signal lights have the whole seal structure,it is waterproof under the bad environment. 4.Lamp holder and the base adopt plug-in type,can replace the up and down bulb as open the cover. 5
Marine Flood Light Ship Searchlight Spot Light
---Equipped focus nut under the ligjt shell and can adjust lighting focus; --- With the grid and joy stick inside, the light can flow the lighting signal according to the requirement. --- It is able to retate for 180 degree horizontally and pitching 30 degree by the lift-hole or controller. ---Confirm to the International Regulations for Preventings Collision at Sea, 1972 and Grade Entry Norms for Steel Ships. ---Conform to the International Standard IEC60598-1-2008 . --