Electric Centrifugal Pump

6/4D-G Series Mechanical Seal Pump V-type V-belt drive ISO9001 Description This series of pump body and the pump adopts special clamp clamping pump cover, pump outlet direction at any position of 360 degrees, convenient installation and use. The bearing assembly adopts a cylindrical structure, which is convenient for adjusting the clearance between the impeller and the pump body, and can be integrally dismantled during maintenance. The bearings are lubricated by grease. Seal

G and GH Series sand suction pump , Multistage Centrifugal Pump Description Structure: horizontal, single pump structure of the centrifugal pump. The pump body and the pump cover are clamped by special clamps, and the outlet direction of the pump can be located at any position of 360 degrees. The installation and use are convenient. The bearing assembly adopts a cylindrical structure, which is convenient for adjusting the clearance between the impeller and the pump body, and

50B-L Low Abrasive Centrifugal Slurry Pump horizontal double shell axial suction Description L series sturdy solid mud pump bow. It employs the same design point of "" (R) and higher efficiency, the impeller plus at an attractive initial cost. Designed for rugged duties while providing greater efficiency, the L series is a combination of proven (R) unique features. L series solid solid mud pump bow. It employs the same design point (R) and higher efficiency, the impeller

350S-L R Centrifugal Slurry Pump 0.7kw ~ 559kw Power ISO9001 Description L series pump incorporates the same design points of the pump, but with a wider range of flow-rates and lower life-cycle costs. Corrosion resistant rubber or polyurethane lining and impellers for highly corrosive slurries can be interchanged with (M) series metal parts; By explosion proof motor or diesel engine ZV / Cr / CV / DC type Discharge size 1 "to 18" Capacity up to 1000 liters / sec,

100DL Low Abrasive Slurry Pump Part Code Number Packing Gasket D067 Cover Plate DL10013 Frame Plate DL10032 Frame Plate Liner Insert 64041 Volute Liner Seal D10124 Volute Liner DL10110 Impeller 64056 Shaft Sleeve,Short D075 Stuffing Box DSC078 Expeller DSC028 Expeller Ring DSC029 Base D003M Lantern Ring D063 Lantern Restrictor D118 Split Packing Gland D044 Inlet Gasket DL10060 Outlet Gasket DL10132 End Cover Gasket D025 Bearing Housing D004M End Cover D024 Labyrinth (Wet End)

150E-L slurry pump 1.8~2844 m3/h Flow Expeller seal Sealing type Description L series sturdy solid mud pump bow. It employs the same design point of "" (R) and higher efficiency, the impeller plus at an attractive initial cost. Designed for rugged duties while providing greater efficiency, the L series is a combination of proven (R) unique features. The pumps are available with interchangeable liner options, including metal and various grades of elastomers

100D-L Centrifugal Slurry Pump / Mining Slurry Pump ZVZ Drive Description The pump is available with interchangeable liner options including both metal and various grades of elastomer depending on the application. L series pump incorporates the same design points of the pump, but with a wider range of flow-rates and lower life-cycle costs. Higher efficiency impellers make the L Series a valuable feature in any plants. Applications Plant Water Supply Thickener Overflow

20A-LGEM Centrifugal Slurry Pump , Horizontal Centrifugal Slurry Pump Description The L series pump is a cantilever and horizontal centrifugal slurry pump. This machine is suitable for the transportation of abrasive and high-density mud in metallurgy, mining, coal, electric power, building materials and so on. Pump frames, plates, linings and impellers are made of hard metal. The seal of the pump shaft may be sealed by shaft or centrifugal shaft. The discharge branches can be

450ST-L Horizontal Slurry Pump Expeller seal Sealing type OEM Description L series sturdy solid mud pump bow. It employs the same design point as the (R) and higher efficiency. In the coal washing industry, slurry pump base, due to different working conditions, large coal gangue, easy to plug, slurry pump impeller, the design of slurry pump high demand. In general, the slurry concentration is low at 0-15%, 15% - 30% is medium, and more than 30% is generally called high

300S-L(R)Gempump Low Abrasive Slurry Pump Mining Slurry Pump Cantilever and horizontal double shell axial suction Description L series Rugged heavy duty slurry pump for medium to lower heads.It incorporates the same design points of the (R) and plus higher efficiency impellers at an attractive initial cost.Designed for rugged duties while offering higher efficiencies, the L series is a combination of the proven (R) unique features. Higher efficiency impellers make the L

300TV-SPGEM Mining Slurry Pump Vertical Single Stage Suction Cantilever Centrifugal Slurry Pump Description The pump has a single shell structure, light weight, small size, easy installation and maintenance. The 300TV-SPGEM(R) mud pumps are heavy, vertical, centrifugal and can work in sinks and pools. The material of flow passing parts is based on different characteristics of different pulp in industrial field, and selects suitable corrosion resistant and corrosion resistant

250TV-SPGEM high pressure slurry pump single shell structure 5.4~352 L/s Flow Description The pump has a single shell structure, light weight, small size, easy installation and maintenance. The shell is made of wear-resistant metal, the impeller by the wear-resistant metal or natural rubber, polyurethane and synthetic rubber. Depending on the fluid in the pool, different shaft lengths and straw sizes can be selected. They are designed to pump the slurry with abrasive, large

200SV-SPGEM Centrifugal Slurry Pump Mechanical seal Sealing type Description 200SV-SP(R)GEM vertical mud pump is a kind of centrifugal mud pump immersed in water tank, cantilever design. With double suction and half open impeller, the agitator can keep the solids in suspension. The SPRGEM model uses full rubber corrosion resistant covering and recessed impeller for excessive material selection; full elastic lining or carbide. No submerged bearings or packings. Large capacity

150SV-SPGEM Vertical Sump Pumps engine BD/DC type Discharge size 44-200mm Vertical sump pumps Sump pump Slurry pump Description The pump has a single shell structure, light weight, small size, easy installation and maintenance. The 150SV-SPGEM(R) mud pumps are heavy, vertical, centrifugal and can work in sinks and pools. These pumps do not require any shaft seal and seal water, even if the intake is insufficient to work properly. Applications coal mining environmental

100RV-SPGEM Vertical Centrifugal Slurry Pump for conveying abrasive Specification of vertical sump pump The SPGEM/SPRGEM heavy duty cantilever sump pump is designed for applications requiring greater reliability and durability than conventional vertical process pump can offer. The heavy duty cantilever design makes the SPGEM/SPRGEM sump pump ideally suited for heavy continuous handling of abrasive and corrosive liquids and slurries whilst submerged in sumps or pits. 1.Flow:

65QV-SPGEM galigher vertical sump pump / Vertical sump pumps Vertical Sump Pump Description The 65QV-SP(R)GEM mud pumps are heavy cantilever pump is a vertical and centrifugal mud pump. It is suitable for handling large size abrasive, coarse particles, high concentration or corrosive dense large particles of thick slurry. SPGEM pump immerdsed all parts of the liquid are equipped with rubber lining, suitable for deep working conditions, conveying non edge grinding. SP GEM

Material Pump Description Standard Material Material Options Shaft 4140 Mild Steel Available on Request Bearing Housing Cast Iron Column Mild Steel Upper Strainer Rubber Cast Iron Lower Strainer Cast Iron Back Liner 27% Chrome White Iron Pump Casing 27% Chrome White Iron Rubber Lined White Iron Impeller 27% Chrome White Iron Rubber Discharge Pipe Mild Steel Rubber Lined Mild Steel/ Composite Adaptor Plate Mild Steel 40PV-SPGEM Centrifugal Slurry Pump / Vertical sump pumps

10/8ST-GEM Centrifugal Slurry Pump 468-1008 m3/h , Heavy Duty Slurry Pump China Centrifugal Pumps, Horizontal Slurry Pumps Type 8x6S -HH slurry pumps are cantilevered, horizontal, centrifugal slurry pumps. The 8x6S -HH slurry pumps is a type of centrifugal pump, vane pump principle or peristaltic hose pump physics, increase the mixture of liquid and solid particles (aka the slurry pressure), by centrifugal force (a rotating impeller) and conversion of electrical energy into

6x4S-HH Horizontal Centrifugal Pump Mechanical seal Sealing type Centrifugal Pumps, Horizontal Slurry Pumps The 6x4s - HH slurry pump is a horizontal cantilever centrifugal slurry pump,. The frame, lining plate and impeller of the screw pump are made of wear-resistant metal. Sealing or sealing devices are available for HH series shaft seals. The discharge branch can be oriented to either of the eight positions to fit the installation and application. The utility model can be

6x4F-HHGEM Centrifugal Slurry Pump , High Head Centrifugal Pump​ China Centrifugal Pumps, Horizontal Slurry Pumps 6x4F-HHGEMmud pump can be widely used in power, building materials, metallurgy, coal, mining and other industrial sectors to transport strong, high concentration slurry. With replaceable metal lining, high head can be supplied under high pressure. A large flow passage pump series suitable for conveying large slurries of gravel, mud, and solids. Used in long