Wear Resistant Castings

45 Degree Schedule 80 Seamless Carbon Steel Pipe Fitting Elbow With Flange Introduction: * 45°, 90°, and 180° Elbows (Other degrees available on request and POA) * 3R Elbows - 45° & 90°, segmentable and non-segmentable. * Straight Tees * Reducing Tees and Elbows * Concentric and Eccentric Reducers * Caps and Stub Ends * Crosses and Laterals Chemical Composition: Composition (%) C Mn Si Cr Cu P S Hardness Cr2 1.8-3.6 0.5-1.5 ≤1.0 1.5-3.5 ≤1.0 ≤0.06 ≤0.06 About HB430 (Eqv.HRC45

Customized Processing of HT250 Gray Iron Sleeve Wear-resistant Castings Special Features: 1. We can make Gray Iron Tube Castings with Centrifugal Cast Process. 2. We can supply finished Gray Iron castings with machining process. 3. We can produce Gray Iron castings as per international standards. Production Process:Centrifugal Cast Process, including machining process. Quality Level: As per National Standard & International Standards. Application Field: Mining Industry, Valve

56-62HRC AS2027 High Wear Resistance Chrome Wear Plate Impact Crusher Wear Liner Product Description: NiHard is a well-established white iron product alloyed with nickel and chromium to give significant abrasion and impact resistant properties. The structure of NiHard is composed of iron and chromium carbides, fixed in a matrix rendered martensitic by the nickel content. This structure allows NiHard to be utilised in abrasive and high impact conditions found throughout the

56-62HRC AS2027 Nihard 4 Wear Liners Wear Billets for Chute Protection Product Description: NiHard is a well-established white iron product alloyed with nickel and chromium to give significant abrasion and impact resistant properties. The structure of NiHard is composed of iron and chromium carbides, fixed in a matrix rendered martensitic by the nickel content. This structure allows NiHard to be utilised in abrasive and high impact conditions found throughout the construction

QT500-7 Ductile Iron Impeller Centrifugal Pump Impeller Centrifugal Ductile Iron Pump Impeller We use resin sand technology; Classification: 1. Closed impeller: consists of blades and front and rear cover plates. The closed impeller is more efficient and difficult to manufacture. It is most used in centrifugal pumps. It is suitable for conveying clean water, solution and other clean liquids with low viscosity without particles. 2. Semi-open impeller: Generally, there are two

Cr15MoNi High Cr Cast Iron Wear Plates Ni-hard Cast Iron Plates Product Description: Special Features: 1. Good surface finish; 2. We use Sand Cast Process to produce the Ni-hard white iron plates. 3. We do quenching & tempering treatment to achieve better wear performance. 4. Specifically designed and manufactured by Welding Alloys, wear plates comprise a base plate of construction steel and a wear resistant coating applied by arc welding, offering exceptional resistance to

High Cr Impact Crusher Blow Bars Impact Crusher Spare Wear Parts 1. Product Description: The impact crusher hammer has various shapes, including long strip, I-shaped, T-shaped, S-shaped and axe-shaped. The principle of the crusher to choose the shape of the hammer is easy to fasten and increase the service life. It is important to choose the quality and shape of the hammer reasonably. 2. Advantages: Wear-resistant but not fragile, long life. 3. Model: 1010, 1210, 1214, 1315,

Gray Iron Cylinder Liner,HT250 Cylinder Liners,Cast Iron Cylinder Liner Special Features: 1. We can make Gray Iron Tube Castings with Centrifugal Cast Process. 2. We can supply finished Gray Iron castings with machining process. 3. We can produce Gray Iron castings as per international standards. Production Process:Centrifugal Cast Process, including machining process. Quality Level: As per National Standard & International Standards. Application Field: Mining Industry, Valve

Q235B,45 Steel,Carbon Steel Counterweight Block,Clump Weight 1. Product Description: Clump Weights are weights used to add weight to maintain balance.The counterweight iron process can be divided into three basic parts, namely counterweight iron metal preparation, mold preparation and casting processing. Counterweight iron metal refers to the metal material used for casting castings in the production of counterweight iron. It is an alloy composed of one metal element as the

HRC32-43 Pearlite CrMo Alloy Steel Lifting Bar,Mine SAG Lifter Bars 1.Material Grade:AS 2074/L2A, AS 2074/L2B,AS2074/LC; 2.Size:120 x 171.6 x 50mm,240 x 165 x 60mm,240 x 175.8 x 60mm,etc; 3.Process:Sand Casting; 4.Hardness:HRC32-43; 5. Suface Finish:Ra.100; 6. The size tolerance:As per CT13; 7. Application:Mine,Ball,SAG and Cement Mill; 8. Package:Packed by steel crates. 9.Chemical Composition: Composition(%) C Si Mn Cr S P Mo Cu Ni AS 2074/L2B(modified) 0.55-0.75 ≤0.75 0.50

NiCr4-600 Cement Kiln Segments Kiln Alloy Chromium Wear Resistance Lining Plate Mill Liners Features: 1. Material: High Cr Cast Iron & Ni-hard Cast Iron 2. Hardness:More than HRC60 3. Partially or fully machining with special cutting tools. 4. Advantage of our Heat Treatment: - Professional, specific furnace, single-minded - Vertical pit furnace,keep the temperature uniformity during heating,+/-1℃ - Small deformation,little oxide layer,reduce material cost - Different

63RHC Cast Iron Casting Chocky Bar Laminated Wear Buttons and Wear Plate Wear Bars Blocks Product Description: NiHard is a well-established white iron product alloyed with nickel and chromium to give significant abrasion and impact resistant properties. The structure of NiHard is composed of iron and chromium carbides, fixed in a matrix rendered martensitic by the nickel content. This structure allows NiHard to be utilised in abrasive and high impact conditions found

AS2027 NiCr4-600 Wear Liner Plates for Chutes and Hopper Protection Product Description: NiHard is a well-established white iron product alloyed with nickel and chromium to give significant abrasion and impact resistant properties. The structure of NiHard is composed of iron and chromium carbides, fixed in a matrix rendered martensitic by the nickel content. This structure allows NiHard to be utilised in abrasive and high impact conditions found throughout the construction,

AS2027 NiCr4-600 China Factory Wear Resistance 60HRC Ni-hard Wear Liner Plates Product Description: NiHard is a well-established white iron product alloyed with nickel and chromium to give significant abrasion and impact resistant properties. The structure of NiHard is composed of iron and chromium carbides, fixed in a matrix rendered martensitic by the nickel content. This structure allows NiHard to be utilised in abrasive and high impact conditions found throughout the

Cr15Mo2 High Chromium Cast Iron Plates,High Cr Casting Parts of Cars,Wear-resisitant Iron Plates EB11016 1. Product Name:Cr15Mo2 High Chromium Cast Iron Plates,High Cr Casting Parts of Cars,Wear-Resisitant Iron Plates 2. Material Grade:Cr15Mo2 3. Size:340 x 66 x 26mm 4. Process:Casting 5. Dimensional Tolerance:CT10 6. Surface Roughness:Ra100 7. Other special requirements:As your drawings 8. Chemical Composition: Composition (%) C Cr Si Mn Cu Ni Mo P S Hardness (HRC) Cr15Mo2 2

D505x63mm 45 Carbon Steel Sheave,High Quality Cast Steel Rope Sheave, Custom Open Die Forging Sheave EB24036 Technical parameters: Size: Sheaves:D505mmx63mm(Groove bottom dia); Wire rope Dia: 12mm; Weight: According to Customer’s Drawings Material: Sheaves: 45#Steel 45#Steel C Si Mn Cr S P Cu Ni 0.42~0.50 0.17~0.37 0.50~0.80 ≤0.25 ≤0.035 ≤0.035 ≤0.25 ≤0.25 Commercial Terms: Delivery time 30 work days after the receipt of payment. Payment terms 40% deposit in advance and

High Cr Mo Steel Lifter Bar Embedded into Rubber for SAG & AG Mill Lifter Bar EB6025 Mill liners protect the cylindrical structure of the mill from wear.Thus the main wear parts in these mills are the balls themselves, and the liners. The balls are simply "consumed" by the wear process and must be re-stocked, whereas the liners must be periodically replaced. The ball and tube mills are low-speed machines that grind the coal with steel balls in a rotating horizontal cylinder.

High Cr Alloy Steel Casting Of Lifter Bar , High Hardness And Wear Resistant EB6066 Quality High Hardness and Wear Resistant High Cr Alloy Steel Casting of Lifter Bar Mill liners protect the cylindrical structure of the mill from wear.Thus the main wear parts in these mills are the balls themselves, and the liners. The balls are simply "consumed" by the wear process and must bere-stocked, whereas the liners must be periodically replaced. The ball and tube mills are low-speed

Ni-hard Plate 4 600 Ni Hard Casting EB10009 Special Features: 1.Good surface finish; 2.We use Sand Cast Process to produce the Ni-hard white iron liners. 3.We do quenching & tempering treatment to achieve better wear performance. Chemistry Standard for Ni-hard White Iron Materials: ISO 21988/JN/ HBW C Si Mn P S Ni Cr Eqv.Standards HBW480Cr2 480 2.5-3.0 0.8 0.8 0.10 0.10 3.0-5.5 1.5-3.0 BTM Ni4Cr2-DT EN-GJN-HV520 AS2027 NiCr2-500 ASTM A 532 Ni-Cr-Lc HBW500Cr9 500 2.4-2.8 1.5-2

AS2027 NiCr2- 500 Ni-hard Cast Iron Mine Mill Liner EB10010 Material Grade:Ni-hard Cast Iron Dimensions:as per drawings Special Features: 1.Good surface finish; 2.We use Sand Cast Process to produce the Ni-hard white iron liners. 3.We do quenching & tempering treatment to achieve better wear performance. 4.Chemistry Standard for Ni-hard White Iron Materials. ISO 21988/JN/ HBW C Si Mn P S Ni Cr HBW480Cr2 480 2.5-3.0 0.8 0.8 0.10 0.10 3.0-5.5 1.5-3.0 HBW500Cr9 500 2.4-2.8 1.5-2