Nickel Based Alloys

Super Invar 32-5 Round Bar/ Rod ,Nickel Iron alloy Rod 1. Invar 36 (FeNi36) Invar 36, also known as FeNi36, is a nickel-iron, low-expansion alloy containing 36% nickel. It has a low coefficient of expansion from cryogenic temperatures to about 260°C. In the dry air at home temperature, invar 36 has good resistance to corrosion. But in moist air, it may go corrosion. Chemical Composition Grade C% Si% P% S% Mn% Ni% Fe% Invar 36 Max 0.05 Max 0.30 Max 0.020 Max 0.020 0.20-0.60 35

Invar 36/4J36 sheet/plate precision alloy , invar 36 plate invar 36 sheet Invar 36 has a low coefficient of expansion from cryogenic temperatures to about 260°C. It is also retains good strength and toughness at cryogenic temperatures. Invar 36 is used to making aerospace composites, standards of length, measuring devices, thermostat rods, laser components, clock pendulums and tanks and piping for the storage and transportation of liquefied gases. Features: Invar 36 is a 36%

​Invar 36 Sheet, also known as Nickel Alloy 36 Plate, is a nickel-iron alloy noted for its uniquely low coefficient of thermal expansion & contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel. Invar 36 Coils is magnetic at temperatures below its Curie point and non-magnetic at temperatures above. Invar 36 Sheet is the standard alloy for low expansivity up to 400

Inconel X750 Spring / UNS N07750 / NiCr15Fe7TiAl, NC15FeTNbA, NCF750,GH4145 Inconel X-750 spring alloy is mainly used in the manufacture of corrosion-resistant planar wave springs, circumferential coil springs, helical compression springs, spring rings and seals for aeronautical engines operating below 540 °C. Inconel X750 wire / UNS N07750 / DIN W. Nr. 2.4669 Inconel X-750(USA),NiCr15Fe7TiAl(Germany),NC15FeTNbA(France),NCF750(Japan),GH4145 Inconel X-750 spring alloy is

Inconel X750 Spring Wire / UNS N07750 / DIN W. Nr. 2.4669 high tensile strength Inconel X-750 alloy is mainly used in the manufacture of corrosion-resistant planar wave springs, circumferential coil springs, helical compression springs, spring rings and seals for aeronautical engines operating below 540 °C. Inconel X750 wire / UNS N07750 / DIN W. Nr. 2.4669 Inconel X-750(USA),NiCr15Fe7TiAl(Germany),NC15FeTNbA(France),NCF750(Japan),GH4145 Inconel X-750 alloy is mainly nickel

Inconel Pipe fittings ( Elbow, Reducer , Tee , Nipples , Stub End) EN10204 ASME B16.9 Material : Inconel 600, Inconel 601,Inconel 625,Inconel 686,Inconel 690,Inconel 718, Inconel X-750,Inconel 740,Inconel 617 Inconel® Alloy Butt weld Seamless Pipe Fitting, Inconel Welded Pipe Fittings Suppliers, Inconel® 45°/90°/180° Butt weld Elbow, Nickelvac® Pipe Fittings, Nickel Alloy ANSI B16.9 Short & Long Radius Elbow, Inconel Equal Tee, ASME B16.28 600 Inconel® Alloy Butt weld

Inconel 625 tube UNS N06625 / DIN W. Nr. 2.4856 AMS 5581, ASTM B829 Inconel 625 tube / UNS N06625 / DIN W. Nr. 2.4856 ASTM B444, ASTM B751, ASTM B829, ASTM B775, ASTM B705, ASTM B704, AMS 5581 fabricated to order (welded, with 100% x-ray inspection. Alloy 625 tube shows excellent corrosion resistance in many media. Excellent resistance to pitting, crevice corrosion, intergranular corrosion and erosion in chloride media. Inconel 625 nickel chromium alloy is widely used because

Inconel 625 welding wire / UNS N06625 Straight, Coil, 0.8mm, 1.2mm, 2.4mm Inconel 625 welding wire Inconel 625 / UNS N06625 / DIN W. Nr. 2.4856 Inconel 625 corresponding wire ERNiCrMo-3 AWS A5.14 Used for welding 625 (N06625) alloy and 20 alloy, 825, 25-6Mo, 9% Ni steel or other molybdenum-containing steel, etc. It can also be used for welding and welding of materials on the surface of dissimilar materials. High temperature and ultra-low temperature mechanical properties,

MP35N alloy wire Diameter 1.5mm/3mm AMS 5844 260 to 300 ksi (1793-2086 MPa) MP35N alloy wire is a non-magnetic nickel cobalt chromium molybdenum alloy, which has unique ultra-high tensile strength (up to 300ksi [2068mpa], good ductility, toughness and very good corrosion resistance. In addition, the alloy also exhibits outstanding resistance to vulcanization, high temperature oxidation and hydrogen embrittlement. The unique properties of mp35n are obtained by work hardening,

Hastelloy Alloy G30 Rod / UNS N06030 / DIN W. Nr. 2.4603 ASTM B581 Hastelloy Alloy G30 Rod / UNS N06030 / DIN W. Nr. 2.4603 ASTM B581 . Hastelloy G30 is a high chromium content nickel-based alloy. It has superior corrosion resistance to commercial phosphoric acid and many highly oxidizing acid media in mixed environments such as nitric acid/hydrochloric acid, nitric acid/hydrofluoric acid and sulfuric acid, compared to most other bases and iron-based alloys. Hastelloy G30

Alloy 52 wire UNS K95050 N14052 ASTM F30 for welding filler rod Diameter 3.2mm The Ductility-Dip Crack (DDC) existed in the nickel base alloy weldment during the high heat input GTAW cladding processwhere Alloy 52 is used as filler metal. This study is focused on the formation mechanism of DDC and its influencing factor. The formation temperature range is known asthe Ductility-Dip Temperature Range (DTR). The Failure Map of Alloy 52 was constructed by changing the temperature

Alloy 52 Rod UNS K95050 N14052 ASTM F30 glass metal sealing, electronic area Alloy 52 Rod / N14052 Alloy 52 contains 52% nickel and 48% iron and is widely used in the telecommunications industry. It also finds application in a wide variety of electronic applications, especially for glass seals. Also known as: Pernifer 502, NILO 50, Glass Seal 521 UNS K95050 N14052 ASTM F30 Alloy 52 is a ferronickel alloy with nickel content of 50.50%. It is used for glass metal sealing. When

Alloy 42 Rod NILO alloy 42 electrical glass or ceramics NILO 424, Glass Seal 421 Alloy 42 bar belongs to a controlled expansion alloy Similar called: 4J42, Nio 42, NI42 Fe42Ni (UNS K94100 /ASTM F30) (aka Pernifer 402, NILO 424, Glass Seal 421). Alloy 42 Rod , Alloy 42 Bar Characteristics: The expansion coefficient is matched with the material to be sealed, and the plasticity is good. Easy to process, no phase change occurs in the working temperature range, good electrical

Alloy 42 Sheet Plate NILO alloy 42 electrical glass or ceramics Alloy 42 Sheet Nilo 42 (UNS K94100 /ASTM F30 / 1.3917) Grade: 4J42|Nilo 42|FeNi42|K94100|Alloy 42 Alloy 42 variety specification and supply status: the variety includes bar, pipe, plate, strip and wire. Alloy 42 smelting and casting process: smelting with non vacuum induction furnace, vacuum induction furnace or electric arc furnace. Application and special requirements of alloy 42: Alloy 42 is a typical brand of

Alloy 42 Foil NILO alloy 42 (UNS K94100/W. Nr. 1.3917) electrical glass /ceramics NILO alloy 42 (UNS K94100/W. Nr. 1.3917), a binary nickel-iron alloy containing 42% nickel. It has a low, and nominally constant, coefficient of expansion over the range 20-300°C (85-570°F). It is used for tooling for aerospace composites, thermostat rods, for semiconductor lead frames, in thermostatic bi-metal strip, and for glass sealing applications in microelectronic components, vacuum

Hastelloy C276 welding wire NiCrMo filler metal developed for MIG / TIG welding ERNiCrMo-4 - Nickel C 276 TIG Welding Rod HASTELLOY- C-276 RTW- Filler Metal Hastelloy C276 Welding Wire UNS N10276 ERNiCrMo-4 HASTELLOY- C-276 Coated ElectrodesAlloy C276 is a nickel-chromium-molybdenum filler metal developed for MIG and TIG welding Hastelloy C-276 / UNS N10276 / DIN W. Nr. 2.4819 welding wire Alloy C276 is a nickel-chromium-molybdenum filler metal developed for MIG and TIG

Hastelloy C276 Rod UNS N10276 / DIN W. Nr. 2.4819 ASTM B574 corrosion resistance Hastelloy C-276 / UNS N10276 / DIN W. Nr. 2.4819 Hastelloy C-276 is a tungsten-nickel-chromium-molybdenum alloy with a very low silicon carbon content. As a versatile corrosion-resistant alloy, mainly resistant to wet chlorine, various oxidizing chlorides, chloride solutions, sulfuric acid and oxidizing salts and have good corrosion resistance in low temperature and medium temperature hydrochlori

Kovar Foil Alloy K / K94610 / ASTM F15 , Pernifer 2918, MIL-I-23011 class 1 Kovar foil (Alloy K) is used for high-power transmitting valves, transistor leads and headers, integrated-circuit lead frames, and photography flash bulbs. UNS K94610 Werkstoff Nr 1.3981 DIN 17745 ASTM F 15 AMS 7726 Wire AMS 7727 Bars and Forgings AMS 7728 Sheet, Strip and Plate MIL-I-23011 class 1 AFNOR NF A54-301 S.E.W 385 DILVER P Description Kovar Foil SPECIFICATION ASTM F15 , UNS K94610,

Alloy 46 Foil UNS K94600, controlled expansion alloy for glass and ceramic seals Alloy 46: Consisting of 46% nickel and iron balance, 46 Alloy is a controlled expansion alloy used mostly in electronic applications, especially for glass and ceramic seals. Alloy 46 is also known as Pernifer 462, NILO 464, and Glass-Seal 461 46 Alloy foil Consisting of 46% nickel and iron balance, 46 Alloy is a controlled expansion alloy used mostly in electronic applications, especially for

Alloy 46 Bar Alloy 46 bar UNS K94600, Pernifer 46, NILO 46, Glass Seal 46 46 Alloy bar Consisting of 46% nickel and iron balance, 46 Alloy is a controlled expansion alloy used mostly in electronic applications, especially for glass and ceramic seals. Alloy 46 is also known as Pernifer 462, NILO 464, and Glass-Seal 461. National Electronic Alloys primarily stocks and distributes 46 Alloy. Bar Wire Sheet Plate Forgings Foil Alloy 46 Composition: Grade Chemical Composition (%) C