Flash Memory IC Chip

MOC3041M zero-cross optoisolator with triac driver output, rated for 400V peak. Ideal for 115/240 VAC logic control in solenoids, relays, and motor starters. UL and VDE recognized. High dv/dt immunity ensures reliable switching.

Wide operating voltage 2V-6V, high-current 3-state outputs drive up to 15 LSTTL loads. Low power consumption (80µA max ICC) with 13ns typical propagation delay. Ideal for buffer registers, I/O ports, and bidirectional bus drivers.

Low-cost JFET-input quad op amp with 50pA bias current, 3MHz gain bandwidth, and 13V/us slew rate. Ideal for audio mixers, motor drives, and solar inverters. Available in SOIC-14 package. Operating temp 0°C to 70°C.

Low-power precision instrumentation amplifier with 25μV max offset, 0.1μV/°C drift, and 100dB CMRR. Gain set by one resistor (1 to 1000). Ideal for medical, portable, and sensor applications. Operating temp -40°C to +125°C.

The LM2902MX/NOPB is a quad op amp IC with 100 dB DC gain and 1 MHz bandwidth. It operates from 3V to 32V single supply or dual ±1.5V to ±16V, with low 700 µA supply current. Ideal for transducer amplifiers and DC gain blocks.

Low-voltage single-supply differential comparator with 0.7μs response time and 80μA supply current. Ideal for 3V/5V systems, replaces LM393. SOT-23-5 package, -40°C to 85°C.

High-speed differential amplifier with integrated output limiting clamp. Features 670 MHz bandwidth, 10 ns settling time, and 600 ps clamp recovery. Ideal for ADC drivers, video, and automotive applications. Available in 8-SO PowerPAD package.

LMP8601QMAX is a precision current sense amplifier with 20x fixed gain, 5.5V supply, and -22V to 60V common-mode range. Ideal for automotive transmission control and battery management. AEC-Q100 qualified, 1mV max offset, 90dB CMRR. Reliable for high-side and bidirectional current sensing.

Ultra-low power undervoltage detector with 3V threshold and 1μA quiescent current. Ideal for battery-powered systems, offering precision monitoring in a compact SC70-5 package. Extended temperature range -40°C to 85°C.

Low-voltage quad comparator IC operating from 2.7V to 5.5V with typical supply current of 410μA. Features open-collector output, low saturation voltage, and ground-sensing input. Ideal for portable consumer and industrial applications.

The LM78L05ACMX/NOPB is a fixed 5V linear voltage regulator delivering 100mA output current. Features include input voltage up to 30V, ±5% output tolerance, thermal overload and short-circuit protection. Ideal for battery chargers, portable instrumentation, and LED lighting. Available in SOIC-8 package.

High-efficiency 75V 1.5A buck regulator with integrated 330mΩ MOSFET. Features 6V-75V input, adjustable frequency 50-500kHz, and AEC-Q100 automotive grade. Ideal for industrial and automotive power supplies.

The LM5117PSQ/NOPB is a wide input range synchronous buck controller with emulated peak current mode control. It features 3.3A peak gate drives, programmable frequency up to 750 kHz, and precision 1.5% voltage reference. Ideal for automotive and industrial DC-DC applications. AEC-Q100 qualified.

High efficiency monolithic synchronous buck regulator with 1.6V to 5.5V input range. Delivers 250mA output current at 93% efficiency. Features 2.25MHz constant-frequency operation, internal soft-start, and low ripple Burst Mode. No Schottky diode required. Available in compact 2x3mm DFN package.

The LT3470ETS8#TRPBF is a 40V input, 200mA output micropower step-down regulator with integrated boost and catch diodes. Features 26μA quiescent current, low ripple

The LT3082ETS8 is a 200mA low dropout linear regulator with programmable output to 0V. Paralleling enables higher current or heat spreading. Features reverse-battery protection, stable with 2.2μF ceramic capacitors, and low 33μVRMS noise. Ideal for surface mount power supplies.

High-efficiency synchronous battery charger with hybrid power boost mode for Intel CPU turbo. Supports 1-4 cell Li+ batteries from 4.5-24V adapter. Features ±0.4% charge voltage accuracy, programmable current limits, and enhanced safety protections. Ideal for notebooks, ultrabooks, and portable equipment.

High-efficiency synchronous buck battery charger with SMBus control. Supports 1-4 cell Li-ion with ±0.5% voltage accuracy. Features automatic power source selection, programmable current limits, and enhanced safety protections. Ideal for portable and industrial equipment.

Highly integrated Li-Ion/Li-Polymer switch-mode charge controller with ±0.5% voltage accuracy. Supports 1S-6S cells, up to 10A charge current, and includes safety protections. Ideal for portable, industrial, and medical equipment.

Highly integrated switch-mode battery charger with 90% efficiency and 3A charge current. Features NVDC power path management, I2C control, and boost mode up to 5.5V at 1.5A. Ideal for power banks and portable devices.