Hydraulic Cylinder Parts of TlT Axial Fan

336/100 Guide Housing(Upper) 液压缸部件 活塞杆,齿杆——连接控制阀芯组一起是液压缸的血管和心脏部位. 导向壳体——控制液压活塞左,右运动,带动指示机构操作,便于观察全开和全关. 液压壳体——液压传动的指挥腔室,控制进油,回油,左右方向,指挥全开或全关. 连接法兰——便于固定在风机支撑体上,利用缸体来回调节推盘,调节杆带动叶片全开全关. Hydraulic cylinder component Piston rod, toothed rod - Connecting the control spool group together are the blood vessels and heart parts of the hydraulic cylinder. Guide housing - control the hydraulic piston left and right movement, drive the indicating mechanism operation, easy to observe the

400/125 Hydraulic Housing(lower) 液压缸部件 活塞杆,齿杆——连接控制阀芯组一起是液压缸的血管和心脏部位. 导向壳体——控制液压活塞左,右运动,带动指示机构操作,便于观察全开和全关. 液压壳体——液压传动的指挥腔室,控制进油,回油,左右方向,指挥全开或全关. 连接法兰——便于固定在风机支撑体上,利用缸体来回调节推盘,调节杆带动叶片全开全关. Hydraulic cylinder component Piston rod, toothed rod - Connecting the control spool group together are the blood vessels and heart parts of the hydraulic cylinder. Guide housing - control the hydraulic piston left and right movement, drive the indicating mechanism operation, easy to observe

400/125 Piston rod toothed rod 液压缸部件 活塞杆,齿杆——连接控制阀芯组一起是液压缸的血管和心脏部位. 导向壳体——控制液压活塞左,右运动,带动指示机构操作,便于观察全开和全关. 液压壳体——液压传动的指挥腔室,控制进油,回油,左右方向,指挥全开或全关. 连接法兰——便于固定在风机支撑体上,利用缸体来回调节推盘,调节杆带动叶片全开全关. Hydraulic cylinder component Piston rod, toothed rod - Connecting the control spool group together are the blood vessels and heart parts of the hydraulic cylinder. Guide housing - control the hydraulic piston left and right movement, drive the indicating mechanism operation, easy to observe

336/100 Piston rod toothed rod 液压缸部件 活塞杆,齿杆——连接控制阀芯组一起是液压缸的血管和心脏部位. 导向壳体——控制液压活塞左,右运动,带动指示机构操作,便于观察全开和全关. 液压壳体——液压传动的指挥腔室,控制进油,回油,左右方向,指挥全开或全关. 连接法兰——便于固定在风机支撑体上,利用缸体来回调节推盘,调节杆带动叶片全开全关. Hydraulic cylinder component Piston rod, toothed rod - Connecting the control spool group together are the blood vessels and heart parts of the hydraulic cylinder. Guide housing - control the hydraulic piston left and right movement, drive the indicating mechanism operation, easy to observe

400/125 Servo Sliding Core Group 伺服滑芯组由控制滑芯,导向轴衬,回导衬组成,是液压缸"心脏". The servo sliding core group is composed of the control sliding core, the guide bushing and the back guide bushing, which is the "heart" of the hydraulic cylinder.

336/100 Servo Sliding Core Group 伺服滑芯组由控制滑芯,导向轴衬,回导衬组成,是液压缸"心脏". The servo sliding core group is composed of the control sliding core, the guide bushing and the back guide bushing, which is the "heart" of the hydraulic cylinder.

336/100 Hydraulic cylinder spindle input shaft 氮化处理: 1.氮化硬度:HRC≥60 2.氮化深度:0.15～0.25mm 3.对不需要氮化部位进行保护(螺孔,螺纹等) Nitriding treatment: 1. Nitriding hardness :HRC≥60 2. Nitriding depth :0.15 ~ 0.25mm 3. Protect the parts that do not need nitriding (screw holes, threads, etc.)

400/125 Hydraulic cylinder main shaft flow oil shaft 氮化处理: 1.氮化硬度:HRC≥60 2.氮化深度:0.15～0.25mm 3.对不需要氮化部位进行保护(螺孔,螺纹等) Nitriding treatment: 1. Nitriding hardness :HRC≥60 2. Nitriding depth :0.15 ~ 0.25mm 3. Protect the parts that do not need nitriding (screw holes, threads, etc.)

Elastic cylindrical pin, cylindrical groove pin φ6*32 安装时注意法兰与轴孔要一起配钻,不可错位,否则会造成圆柱销受挤压弯曲,严重时会断裂.如不选用开口弹簧销,而选用实芯销,势必会导致液压缸内部零件,在超负荷状态下损坏(如活塞杆中连接销断,齿轮齿条损坏,伺服阀芯组受到损伤),而不像开口柱销一样起保险作用,保护内部零件而折断自己,也不易掉落,拆装方便. When installing, pay attention to the flange and shaft hole should be drilled together, not misaligned, otherwise it will cause the cylindrical pin to be squeezed and bent, and will break seriously. If the open spring pin is not selected, and the solid core pin is selected, it

400/125 hydraulic adjustment device 容许工作压力:Pv=63(bar)=6.3MPa 容许推力:F左=737(KN)=75200(KG) F右=707(KN)=72140(KG) 自由缸剖面:A左=1193(cm2/) A右=1193(cm2/) 最大缸容量:Vmax=14913(cm3/) 在调节时间t=60(s)时必须的油量:Qmax=14.9(L) 液压缸系统是动叶可调轴流风机核心的一部分,它的好坏直接关系到设备正常运行,也是出现缺陷概率较大的一部分,在液压缸系统中发生缺陷最多的又是控制壳内部组件,控制壳就形同人的大脑一样支配着人的行为. Allowable working pressure :Pv=63(bar)=6.3MPa Allowable thrust :F left =737(KN)=75200(KG) F right =707(KN)=72140(KG) Free cylinder profile :A left =1193(cm2/) A right =1193(cm2/) Maximum

415/100 hydraulic adjustment device 行程h=100mm允许工作压力 P=30(atu) 空净的液压缸截面 A=13.27(dm2/) 在S=100时的液压缸容积 V=13.27(dm3/) 在S=100和V=10 l/min时的调节时间 t=80(s) 转速n=1000u/min时旋转压力密封上的周速 u=2.36(m/s) 液压缸系统是动叶可调轴流风机核心的一部分,它的好坏直接关系到设备正常运行,也是出现缺陷概率较大的一部分,在液压缸系统中发生缺陷最多的又是控制壳内部组件,控制壳就形同人的大脑一样支配着人的行为. Stroke h=100mm allowable working pressure P=30(atu) Empty cylinder section A=13.27(dm2/) Hydraulic cylinder volume V=13.27(dm3/) when S=100 Adjustment time t=80(s) at S=100 and V=10 l/min Rotation

齿轮除用来传递动力外,还可以改变转动方向,转动速度和运动方式等

型号 内径 外径 厚度 (mm) (mm) (mm) 3200 10 30 14 3201 12 32 15.9 滚动轴承由外圈,内圈,滚动体和保持架四部分组成,圆锥滚子轴承主要适用于承受径向载荷为主的径向与轴向联合载荷.此种轴承分为分离型轴承,其内圈(含圆锥滚子和保持架)和外圈可以分别安装.在安装和使用过程中,可以调整轴承的径向游隙和轴向游隙,也可以预过盈安装. 轴承损坏及超过使用小时,必须更换.