IP20 Wedding Light 22 27 CH Nightclub Party Event Equipment 500W LED Moving Head Spot Light

MF-DM500WBSW BEAM SHARPY MOVING HEAD LED STAGE LIGHT

Specifications:                                                                                                                                                                         

OPERATING MODE

DISPLAY SETTING

Common Fault:                                                                                                                                                                          

Panel Operation:                                                                                                                                                                        

BRIEF

The light panel diagram show as Figure 3, above area is fixture description, below area show fixture real-time status, such as DMX cable status, lamp status, error or information(ps. when there are message hav't been checked, echo 'ERR' in status bar, otherwise echo 'NOR'). Display & operation just like 'Android operation system', when select or set item value, system save the settting immediately. RDM protocol is embed in fixture, user set DMX address via cable using the controller surpport RDM function. when fixture was search by controller, displayer will echo 'RDM' indicate this RDM is work.

 

OPERATION
Operate fixture with touch or encoder/button
The left area is TFT Displayer and touch(product which support touch), chick item or value with finger will to complete operation of set light setting(parameters) or view light state.

The area on the right hand side is rotary encoder with button or key, As auxiliary input interface, if fixture disable touch function, the encoder/key can been choose to set or view the item, and then press the encoder button/key to confirm the selection, rotary

encoder or push key again set the parameter value, finally, Press encoder button/key one again to save value or setting.

Parameter value setting

When the selected item is value need to been modified, the dialog shown in Figure 4 will pop up.

Modify value:Can quickly modify value via pull the slider to the desired position, or click the button of 'up' or 'down' whit finger on the right side to set the exact desired value, another way is roll encoder on the right hand side of panel.

Apply value:When Value had been modified, Then press the bottom of 'apply' in the left corner to apply to the light, but haven't saved;

Save Value:Any time, click on the lower right corner of the "OK" button, the setting will been saved into internal memory.

Boolean parameter setting

when the selected parameters is a Boolean value (such as ON or OFF), can directly modify setting by chick corresponding item, the setting will been saved right now.

When the parameter is a key item, chick corresponding item, a dialog shown in Figure 5 will been popup ask for the confirm. Chick 'sure' to confirm.

Sub Menu(Parameter)

CABLE CONNECTION DMX

Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24AWG, low capacity. Do not use microphone cable or other cable withcharacteristics differing from those specified. Theendconnections must be made using XLR type3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4W)between terminals 2 and 3.

IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.

 

RIGGING(OPTIONAL)

 

Applications:                                                                                                                                                                            

Moving head lights are versatile lighting fixtures used in stage productions, concerts, nightclubs, and other entertainment events. They consist of motorized heads that can move horizontally and vertically to direct light beams. They are used to illuminate performers, create dynamic lighting effects, and enhance visual displays.

Packing:                                                                                                                                                                                     

FAQ:                                                                                                                                                                                          

Q1: What do you sell?
A1: We provide good quality of floodlight, high bay light, explosion proof light, tri-proof light, downlight, and other lighting products, as well as responsible services and reliable after-sales warranty.

Q2: Is it OK to print my logo on led light product?
A2: Yes. We provide ODM and OEM services. Please inform us formally before our production and confirm the design firstly based on our sample.

Q3: How to deal with the faulty?
A3: During the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.

Q4: Can I have a sample order for led light?
A4: Yes, we welcome sample order to test and check quality. One sample or mixed samples are acceptable.

Q5: How long time to ship the goods if place an order?
A5: Usually 7 days for sample or small order,15 working days for bulk order, but sometimes depend on the order quantity.