Heavy Duty Non Spring Motor With Remote Control Parking Barrier Gate Accessories Motor
Parking Barrier Gate Motor Heavy Duty Non-Spring Motor With Remote Control
Barrier Gate Accessories Specifications
|
Barrier Gate Accessories Model |
Non-spring Barrier Gate Motor |
|
Barrier Gate Accessories Working Temperature |
-35℃～+65℃ |
|
Barrier Gate Accessories Voltage |
24/100/240VAC, 50/60HZ |
|
Barrier Gate Accessories Rated power |
200W |
|
Barrier Gate Accessories Relative humidity |
≤90% |
|
Barrier Gate Accessories Remote control distance |
≥30m |
|
Barrier Gate Accessories Net weight |
50kgs |
|
Barrier Gate Accessories Speed |
2.5s-6S |
|
Barrier Gate Accessories Max boom length |
6 meters |
|
Barrier Gate Accessories Protection Degree |
IP44 |
Barrier Gate Accessories: DZ-2228
Communication with customers
1) Q: Connected power and press open/close button but the Barrier Gate Accessories no action?
|
A |
Reason |
Solution |
|
1 |
Fuse blown |
Check the fuse and power in the controller |
|
2 |
The battery of the remote control powered off |
Change a new one |
|
3 |
External protection circuit break or at protecting status |
Open the barrier door and click the OPEN/CLOSE button on the control box |
|
4 |
Same frequency interference |
Check photocell and loop detector |
2) Q: Connected power and press the open/close button, the Barrier Gate Accessories will move but even when it is in the right position, the motor still runs and does not stop.
|
A |
Reason |
Solution |
|
1 |
Limit switch |
Adjust the horizontal/vertical limit switch to the correct position |
|
2 |
Main controller failure |
Change a new one |
3) Q: The motor running but the Barrier Gate Accessories arm is not in action.
|
A |
Reason |
Solution |
|
1 |
Barrier arm at 45° position where is hard to move |
Unlock the clutch and manually rotate the arm to a horizontal or vertical position then try again |
|
2 |
The tension of the balancing spring is not suitable |
Adjust spring exactly |
|
3 |
Low working voltage |
Check the voltage and power |
.
4) Q: When opening/closing, the Barrier Gate Accessories arm cannot reach the right position (90° vertical & 180° horizontal)?
|
A. |
Reason |
Solution |
|
1 |
Length adjustment of connecting rod not correct |
Open the barrier door and unlock the clutch to check when the arm is at 90° vertical position if the master rod covers slave one; when the arm is at 180° horizontal position if the master rod and slave one are in the same straight line |
|
2 |
Nuts on the limit switch loose |
Tighten the nuts when arm at 90° vertical and 180° horizontal
|
What are the advantages of Wonsun Barrier Gate Accessories?
1)The humanized clutch device: in case of power off, unlock the clutch device and raise the boom manually. By the time the power is supplied, lick the clutch device to make it work normally again.
2)Special spring device: Both the compression spring and tension spring can be used in the machine, Using the compression spring can avoid accidents caused by the tension spring.
3)Three control buttons: for Barrier Gate Accessories boom raising, falling, and pausing.
4)Barrier Gate Accessories Boom backtrack function: the boom will rise if hits something when falling.
5)Infrared photocell design: for avoiding the crash when the boom falls, to prevent the vehicles from being pressed.
6)Both external and internal loop detectors are supported.
7)"open", "close" and "stop" controlling interfaces.
8)RS-485 communication serial interface(optional)
9)Barrier Gate Accessories Traffic light signal connection device: red light for stop, green light for pass.
10)Barrier Gate Accessories Remote control and wire control for selection.
Contact information:
Sue Zhang
Skype: SueZhang729
Whatsapp:+86 158 7925 9831
Email:sue@wonsunbarrier.com
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.