Adjustable 0.6s to 6s Automatic Barrier Gate Parking Lot Barrier Gate
Adjustable 0.6s to 6s Automatic Barrier Gate Parking Lot Barrier Gate
1 pcs Automatic Barrier Gate
1 pcs Automatic Barrier Gate arm boom (from 1m to 6m can customized)
1 pcs Automatic Barrier Gate control panel(built inside)
2 pcs Automatic Barrier Gate remote controllers
1 pcs Automatic Barrier Gate manual book
Automatic Barrier Gate Model Selection and Differences
| Automatic Barrier Gate Boom type | Boom Length(L) | Diameter of the spring(mm) | Note | |
| Automatic Barrier Gate Straight boom | 6M≥L≥5M | 5.5/4.5 | ||
| 5M≥L≥4.5M | 5.5 | Dispatching 4.5 | ||
| 4.5M≥L≥3M | 4.5 | Dispatching 4.5 | ||
| Straight boom adhesive tape | 5M≥L≥4M | 4.5M≥L≥3M | 5.5/4.5 | Dispatching 4.5 |
| 4M≥L≥3M | 3.5M≥L≥3M | 4.5 | Dispatching 4.5 | |
| Automatic Barrier Gate Folding boom | 6M≥L≥5M | 6.5/4.5 | ||
| 5M≥L≥4M | 5.5/4.5 | |||
| 4M≥L≥3M | 4.5 | |||
| Two fence boom | 5M≥L≥4M | 6.5/5.5 | ||
| Automatic Barrier Gate Fence boom | 4M≥L≥3M | 5.5/4.5 | ||
| Three fence boom | 4M≥L≥3M | 6.5/5.5 | ||
| 3M≥L≥2M | 5.5/4.5 | |||
Automatic Barrier Gate Specifications
|
Automatic Barrier Gate Model |
DZTP-128-B |
|
Working Temperature |
-40℃～+75℃ |
|
Automatic Barrier Gate Voltage |
220V±10%, 110V±10%, 50/60HZ |
|
Automatic Barrier Gate Rated power |
80W |
|
Automatic Barrier Gate Relative humidity |
≤90% |
|
Remote control distance |
≥30m |
|
Automatic Barrier Gate Net weight |
48kgs |
|
Automatic Barrier Gate Speed |
1S,1.8S,3S, 6S |
|
Max boom length |
6 meters |
|
Motor Rotational speed |
1400rmp |
|
Protection Degree |
IP54 |
Automatic Barrier Gate Advanced Features:
1) A clutch key can be used to open the clutch when power is off.
2)Fan cooling machine reduces the motor temperature by high frequency using, never get heat-protecting, unique temperature calefaction design for low temperature using, prevent freezing in cold weather.
3) An exactitude aluminum alloy die-casting motor base reduces the noise and joint abrasion to prolong the barrier gate's working life.
Why choose us?
1. One year's free servicing is supplied( not including the arm)
2. Lifetiom charged servicing is offered.
3. Technology servicing is supplied
The following situations are charged for servicing (or changing):
1. Broken by wrong installation.
2 Broken by improper voltage.
3. The surfaces of the system were destroyed by the wrong installation our use.
4. Broken by natural disaster.
5. Overdue
6. Servicing items out of our promises.
The upgrade and improvement of the product won't be notified if there is any.
The explaining authority of this product instruction and service article belongs to the production factory.
Communication with customers
1) Q: Connected power and pressed the open/close button but the traffic barrier gate no action.
|
A |
Reason |
Solution |
|
1 |
Fuse blown |
Check the fuse and power in the controller |
|
2 |
The battery of the remote control powered off |
Change a new one |
|
3 |
External protection circuit break or at protecting status |
Open the Automatic Barrier Gate door and click the OPEN/CLOSE button on the control box |
|
4 |
Same frequency interference |
Check photocell and loop detector |
2) Q: Connected power and press the open/close button, the traffic barrier gate will move but even when it is in the right position, the motor still runs and does not stop.
|
A |
Reason |
Solution |
|
1 |
Limit switch |
Adjust the horizontal/vertical limit switch to the correct position |
|
2 |
Main controller failure |
Change a new one |
3) Q: The motor running but the traffic barrier gate arm is not in action?
|
A |
Reason |
Solution |
|
1 |
Automatic Barrier Gate arm at 45° position where is hard to move |
Unlock the clutch and manually rotate the arm to a horizontal or vertical position then try again |
|
2 |
The tension of the balancing spring is not suitable |
Adjust spring exactly |
|
3 |
Low working voltage |
Check the voltage and power |
4) Q: When opening/closing, traffic barrier gate arm cannot reach the right position (90° vertical & 180° horizontal)?
|
A. |
Reason |
Solution |
|
1 |
Length adjustment of connecting rod not correct |
Open the barrier door and unlock the clutch to check when the arm is at 90° vertical position if the master rod covers slave one; when the arm is at 180° horizontal position if the master rod and slave one are in the same straight line |
|
2 |
Nuts on the limit switch loose |
Tighten the nuts when the arm at 90° vertical and 180° horizontal position |
Contact us for pricelist and catalog:
Sue Zhang
Email:sue@wonsunbarrier.com
Skype: SueZhang729
Whatsapp:+86 158 7925 9831
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.