HD-E708-6 Rapid-rate Thermal Cycle Test Chamber (Including Circuit Continuity Monitoring System)
Image above for reference only
- The refrigerating system equips Germany Bock Compressor, and uses environmentally friendly refrigerant (R404a). Adopting binary low temperature circuit system design, it is convenient to use different compressors for work in different temperature regions.
- Temperature control using P.I.D + S.S.R system coordinated control with the same channel. It has the function of automatic calculation, which can immediately modify the temperature change conditions to make the temperature control more accurate and stable.
- High-precision controllers of temperature. The temperature performance is accurately set and displayed with a resolution of 0.1 ℃.
- Temperature system using Nickel-chromium alloy high-speed heating electric wire;
- High temperature system is completely independent;
- The system using stainless steel tube built-in nickel-chromium alloy high-speed heating electric wire and high-temperature magnesium oxide powder, which has fast response and long life;
- The temperature system is completely independent
| Temperature Sensor | High precision PT100 Platinum resistance |
|---|---|
| Controller | TATO |
| Display Function |
|
| Interface |
|
- Protection for Electrical leakage
- Over-temperature
- Compressor overvoltage and overload
- Heater short circuit
| Model | HD-E708-6 |
|---|---|
| Capacity | 6885L |
| Internal dimension(W*D*H) | 1700*1500*2700mm |
| External dimension(W*D*H) | Approx. 3000*3100*3100mm |
| Single sample dimension | 2400*1400*35mm |
| Test sample number | 12 pieces |
| Internal material | SUS#304 stainless steel, mirror finished; |
| External material | Cold-rolled steel plate baking |
| Temperature Range | -40C + 100C |
|---|---|
| Temperature fluctuation | ±0.5℃ |
| Temperature uniformity | ≤2℃ |
| Temperature Rate | Heating Rate: 3.3C/min in linear control @-40~85C |
| Cooling Rate: 3.3C/min in linear control @-40~85C |
| Humidity Range | 20%~95%RH |
|---|---|
| Humidity fluctuation | ±3%RH |
| Humidity uniformity | ±2%RH |
| Temp. &Humid. Chart |  |
| Power Source |
Three-phase, 380V, 50Hz 50KW, 100A |
|---|
| Compressor | Germany Bock compressor |
|---|---|
| Refrigerant | R404A |
| Cooling method | Single stage compression |
| Cooling method | Water cooled(Water tank provide by customer) |
| Heating System | Nichrome stainless steel heater |
| Sample tray | Customized sample holder *1 |
| Testing hole | Diameter 100mm at side of chamber for cable routing |
| Evaporator | Finned tube heat exchanger |
| Dry filter | Absorb the residual moisture and acidic substances in the refrigerant of the refrigeration system, and filter out solid particles, copper shavings, etc. in the system to protect the normal operation of the expansion valve and capillary tube, and prevent ice blocking and dirty blocking. |
| Door handle | Non-reaction, explosion-proof door handle, easy to operate, safe and reliable |
| Insulation | 100mm polyurethane rigid foam and 100mm high density glass fiber cotton |
| Insulation system |
Filling the insulation area with ultra-fine glass fiber; Machine connection parts are made of non-metal resistant high and low temperature materials, which effectively reduces the temperature conduction; Door seal is made of refined silicone rubber, which is more reliable seal; |
| Observation window |
Double-layer vacuum-strengthened glass; Heat-resistant defrosting on the inside with adhesive sheet conductive film, which can clearly observe inner chamber. |
| Note- Interior | The Interior & Bottom (Foundation Plate ) of chamber is Satin finished double walled anticorrosive Stainless steel 304 grade |
- IEC61215:2021 MQT 11 Thermal cycling test
- IEC61215:2021 MQT 12 Humidity-freeze Test
- IEC61215:2021 MQT 13 Damp heat test
- IEC 62892:2021
- IEC 63126:2020
Simulation Animatronic Customer Triceratops are covered with air bubble film before put them into the wooden case, which not only has good shock absorption, impact resistance, heat sealing and also has the advantages of nontoxic, odorless, moisture corrosion, good transparency etc.
If you face any problems in future during testing process we promise we will give you a reply within 48 hours and solution provide within 3 working days. We can offer operation video and English operation muanual. We can provide video-conference. If customers require on-site service, the transport and travel expense shall be borne by customer.
-
Pre-service
24 Hours online service for your consult.
Help choose right model,and a series of service,person,advise.
-
Middle service
Give you best offer
Provide discount for many sets order
Do customer's request:
Choose payment term you convienent.
Promptly production and delivery,inform you in time.
Can provide invoice value as you like to decrease your tax.
-
After sale service
1 year warranty service and all life maintenance.
Technical Egineer are avalible for oversea trainning.
Free change for some parts
Remote control technical consult
Free installation DVD
Maintenance plan
-
Commitment:
We will sign a letter of commitment while we sign the contract, which will improve your confidence to us.
-
Good Packaging:
Good Packaging: Simulation Animatronic Customer Triceratops are covered with air bubble film before put them into the wooden case, which not only has good shock absorption, impact resistance, heat sealing and also has the advantages of nontoxic, odorless, moisture corrosion, good transparency etc.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.