DALI2 DT8 Compatible 26W Constant Current LED Driver with IP20 Stand-by Power ≤0.5W 230Vac
DALI2 DT8 compatiable 26W Constant Current LED driver
【Product Feature】
- Flicker-free for whole dimming range
- Stand-by power below 0.5W
- Primary dimming with push button
- Built-in DALI interface DT8
- Centrally-supplied DC emergency operation DT19
- Protection: short circuit / over temperature/ over voltage
- Derating current for over high ambient temperature
- Push dim with memory function
- 5 year warranty
【Parameter】
| Input | Operating Voltage | 198-264VAC 50Hz /60Hz | ||||||
| Rated Input Voltage | 220-240VAC 50Hz /60Hz | |||||||
| DC Input Voltage range | 200-240VDC | |||||||
| Input Current | 0.14A Max. | |||||||
| Input Inrush Current | <15A (Half current pulse width 100US) @230VAC | |||||||
| Power Factor | ≥0.95 @230VAC (Full load) | |||||||
| Total harmonic distortion | Typical: 15% (@230Vac, 100% load) | |||||||
| Stand-by Power | ≤0.5W(@230Vac) | |||||||
| Efficiency | 86%Max. @230VAC (Full load) | |||||||
| Wiring Method | Push terminal, wire cross section:0.5-1.0mm2 | |||||||
| Loop-in&Loop-out quantity | NO | |||||||
| Automatic circuit breaker (Calculate current in the wire) |
type | B10 | B13 | B16 | B20 | B25 | ||
| Number | 35 | 45 | 56 | 65 | 85 | |||
| type | C10 | C13 | C16 | C20 | C25 | |||
| Number | 22 | 28 | 35 | 45 | 58 | |||
| Output | Operating mode | Constant Current | ||||||
| Load type | LED | |||||||
| Ripple requirement (Flickering or flickering-Free) | Flicker value: less than 2% for whole dimming range | |||||||
| Start up time | <0.7s (@230Vac) | <0.5s (@ DC Input) | ||||||
| No-load output voltage | 60VDC Max. | |||||||
| Load output voltage range | 12-43VDC | |||||||
| Full load output power | 26W Max. | |||||||
| Load output current | 300~600mA : For details<Current gear setting> | |||||||
| Constant current/voltage Precision | Constant Current Precision ±5% | |||||||
| Wiring method | Push terminal, wire cross section:0.5-1.0mm2 | |||||||
| Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max.lead length:20M) | ||||||
| 1-10V Dimming | NO | |||||||
| Dimming Range | Primary PUSH & DALI dimming: 0%-100% | |||||||
| Potentiometer | NO | |||||||
| DALI Dimming | DALI dimming (Max.lead length:300M) | |||||||
| Exception Protection Requirements | Output over temperature protection |
Yes, without self recovery function(Can be inquired) | ||||||
| Output short circuit protection | Yes, without self recovery function(Can be inquired) | |||||||
|
Operating Environment |
Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) | ||||||
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% | |||||||
| Max. case temp(Tc) | 85℃ | |||||||
|
Safety & EMC |
EMC standard | EN55015 EN61547 EN61000-3-2 EN61000-3-3 | ||||||
| DALI protocol standard | IEC62386-101 / 102 / 207 DT6 / 209 DT8 / 220 DT19 | |||||||
| Safety standard | EN61347-1 EN61347-2-13 | |||||||
| Certification | CE | |||||||
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) | |||||||
| Others | IP Rating | IP20 | ||||||
| Type of protection | Class II | |||||||
| Built-in installation | 96*42.5*24mm | |||||||
| Independent installation | 136*42.5*24mm | |||||||
| Blackout memory function | Yes, PUSH blackout memory | |||||||
| PUSH dimming synchronization | 20 units Max. | |||||||
| Packaging requirement | white box+ Instructions Clapboard Outer Carton(K=A) | |||||||
| Weight | 135g | |||||||
| Life | 5 year @Ta full load | |||||||
| Note: All parameters are tested at the input voltage of 230Vac and 25 degree environment unless specified. | ||||||||
【Dimension (Unit:mm)】
【Wiring Diagram】
Fig.A DALI Dimming
Fig. B Push Dimming
【Derating】
【Dimming curve】
【Current gear setting】
| Series | KL26CC-PDii | ||||
| Current(mA) | DIP | Pomax(W) | Uout(V) | ||
| 1 | 2 | ||||
| 300 | - | - | 12.6 | 12～ | 42 |
| 350 | ON | - | 14.7 | 12～ | 42 |
| 500 | - | ON | 21 | 12～ | 42 |
| 600 | ON | ON | 25.2 | 12～ | 42 |
【ON/OFF & Description of Dimming Operation】
A. Short press the PUSH switch (short press time 0.1S-1S), the LED driver will turn on or off.
B. Dimming: Press and hold the PUSH switch (1S-8S), the LED driver can achieve dimming, brightening or dimming, the dimming range is 2-100%.
C. Memory: PUSH dimming has dimming memory function.
D. Dimming synchronization: The power connected to the same PUSH switch can be synchronized by pressing and holding the PUSH switch for longer than 15S
E. DALI dimming mode: Connect the power supply to the DALI system, and it can be dimmed by the DALI host. The dimming range is 0-100%.
【Attention】
1) The LED string must be connected to the load before turning on the input power, otherwise the LED string may be damaged.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.