40W DALI2 DT8 Dimmable LED Driver Constnat Current 500mA To 1050mA While DIP Switches
40W DALI2 DT8 dimmable LED driver constnat current 500mA to 1050mA while DIP switches
【Product Feature】
- Flicker-free for the whole dimming range
- Stand-by power below 0.5W
- Primary dimming with a push button
- Built-in DALI interface DT8
- Centrally-supplied DC emergency operation DT19
- Protection: short circuit / over temperature/ over voltage
- Derating the current for a high ambient temperature
- Push dim with memory function
- 5-year warranty
- Parameters
| Input | Operating Voltage | 198-264VAC 50Hz /60Hz | |||||||
| Rated Input Voltage | 220-240VAC 50Hz /60Hz | ||||||||
| DC Input Voltage range | 200-240VDC | ||||||||
| Input Current | 0.21A Max. | ||||||||
| Input Inrush Current | <15A (Half current pulse width 100US) @230VAC | ||||||||
| Power Factor | ≥0.95 @230VAC (Full load) | ||||||||
| Total harmonic distortion | Typical: 13% (@230Vac, 100% load) | ||||||||
| Stand-by Power | ≤0.5W(@230Vac) | ||||||||
| Efficiency | 86%Max. @230VAC (Full load) | ||||||||
| Wiring Method | Push terminal, wire cross section: 0.75- 1.5 mm2 | ||||||||
| Loop-in&Loop-out quantity | 22PCS(@230Vac) | ||||||||
|
Automatic circuit breaker (Calculate the current in the wire) |
type | B10 | B13 | B16 | B20 | B25 | / | ||
| Number | 20 | 25 | 30 | 45 | 50 | / | |||
| type | C10 | C13 | C16 | C20 | C25 | C32 | |||
| Number | 35 | 48 | 55 | 70 | 90 | 110 | |||
| Output | Operating mode | Constant Current | |||||||
| Load type | LED | ||||||||
| Ripple requirement (Flickering or flicker-free) | Flicker value: less than 2% for the whole dimming range | ||||||||
| Start-up time | <0.7s (@230Vac) | <0.5s (@ DC Input) | |||||||
| No-load output voltage | 68VDC Max. | ||||||||
| Load output voltage range | 12-50VDC | ||||||||
| Full load output power | 40W Max. | ||||||||
| Load output current | 500~1050mA : For details<Current gear setting> | ||||||||
| Output | Constant current/voltage Precision | Constant Current Precision ±5% | |||||||
| Wiring method | Push terminal, wire cross section: 0.75- 1.5 mm2 | ||||||||
| Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max..lead length: 20 M) | |||||||
| 1-10V Dimming | NO | ||||||||
| Dimming Range | Primary PUSH & DALI dimming: 0%-100% | ||||||||
| Potentiometer | NO | ||||||||
| DALI Dimming | DALI dimming (Max..lead length: 300 M) | ||||||||
| Exception Protection Requirements | Output over temperature protection |
Yes, without self-recovery function(Can be inquired) | |||||||
| Output short circuit protection | Yes, without self-recovery function(Can be inquired) | ||||||||
|
Operating Environment |
Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) | |||||||
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% | ||||||||
| Max. case temp(Tc) | 85℃ | ||||||||
|
Safety & EMC |
EMC standard | EN55015 EN61547 EN61000-3-2 EN61000-3-3 | |||||||
| DALI protocol standard | IEC62386-101 / 102 / 207 DT6 / 209 DT8 / 220 DT19 | ||||||||
| Safety standard | EN61347-1 EN61347-2-13 | ||||||||
| Certification | CE | ||||||||
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) | ||||||||
| Others | Degrees of protection | IP20 | |||||||
| Type of protection | Class II | ||||||||
| Built-in installation | 120*64.8*24mm | ||||||||
| Independent installation | 179.6*66.9*24mm | ||||||||
| Blackout memory function | Yes, PUSH blackout memory | ||||||||
| PUSH dimming synchronization | 15 units Max. | ||||||||
| Packaging requirement | white box+ Instructions Clapboard Outer Carton(K=A) | ||||||||
| Weight | 150g | ||||||||
| Life | 5 year @Ta full load | ||||||||
| Note: All parameters are tested at the input voltage of 230VAC and a 25 °C environment unless other specified. | |||||||||
- Dimension (Unit: mm)
- Wiring Diagram
Fig. A DALI Dimming Fig.B Push Dimming
- Derating
- Dimming curve & range
- Current gear setting:
| Current (mA) | DIP | Pomax(W) | Uout(V) | ||||
| 1 | 2 | 3 | 4 | ||||
| 500 | - | - | - | - | 25.0 | 12～ | 50 |
| 550 | ON | - | - | - | 27.5 | 12～ | 50 |
| 600 | - | ON | - | - | 30.0 | 12～ | 50 |
| 650 | ON | ON | - | - | 32.5 | 12～ | 50 |
| 700 | - | - | ON | - | 35.0 | 12～ | 50 |
| 750 | ON | - | ON | - | 37.5 | 12～ | 50 |
| 800 | - | ON | ON | - | 40.0 | 12～ | 50 |
| 850 | - | ON | ON | - | 40.0 | 12～ | 47 |
| 900 | - | - | ON | ON | 39.6 | 12～ | 44 |
| 950 | ON | - | ON | ON | 39.9 | 12～ | 42 |
| 1000 | - | ON | ON | ON | 40.0 | 12～ | 40 |
| 1050 | ON | ON | ON | ON | 39.9 | 12～ | 38 |
- ON/OFF & Description of Dimming Operation
A. Short-press the PUSH switch (short press time 0.1S-1S), the LED driver will turn on or off.
B. Dimming: Press and hold the PUSH switch (1S-8S), the LED driver can achieve dimming, brightening, or dimming, the dimming range is 2-100%.
C. Memory: PUSH dimming has dimming memory function.
D. Dimming synchronization: The power connected to the same PUSH switch can be synchronized by pressing and holding the PUSH switch for longer than 15 seconds
E. DALI dimming mode: Connect the power supply to the DALI system, and it can be dimmed by the DALI host. The dimming range is 0-100%.
- Attentions
1) The driver must be connected to the fixtures before turning on the input power, otherwise the fixtures may be damaged.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.