1x10w Push / 1-10v LED Dimmer Switch / High Efficiency LED Driver 0-10V
ML10C-PV 1x10w 1-10V and push dimmable led driver 350mA 6-30Vdc flicker-free version
Description
1, Flicker-free version,flicker rate less than 2% tested by professional equipment
2, Two circuit design AC-DC-DC, no flicckering in dimming 2%-100%
3. Output constant current 350mA,currency rate ±5%
4, Dimmable LED driver with PUSH DIM, and 1-10V dimming interface.
5, Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores.
6, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch.
7, Maximum length of the cable, from switch to last driver is 20m.
8, Press-in terminals in primary and secondary side, easy assembly.
9, Protection: Short circuit / Over voltage / Over temperature.
10, Long life span 50,000h, 5 years guaranty.
11. It can matches with Merrytek MS01(daylight sessor) and MC003V( microwave motion sensor ) to achieve auto on-off, dimming and daylight funcion
Specifications
|
INPUT
|
Input voltage |
220-240Vac |
|
Input frequency |
50-60Hz |
|
|
Input current |
0.06A max |
|
|
Power factor |
≥0.90 |
|
|
Efficiency(Note1) |
≥76% |
|
|
Stand-by power (Note 2) |
≤0.5W |
|
|
OUTPUT
|
Output current/voltage and load |
350mA 6-30Vdc 10.5w max |
|
Output load range |
1x10.5W max |
|
|
Current accuracy |
±5% |
|
|
Dimming mode |
0-10V, PUSH |
|
|
ENVIRONMENT
|
Working temp.(Ta) |
-20~50℃ |
|
Surface temp.(Tc) |
85℃max |
|
|
Working humidity |
20~85%RH non-condensing |
|
|
Storage temp. |
-40~80℃ |
|
|
Life time |
≥50000hours |
|
|
PROTECTION
|
Isolation class |
Class II, SELV |
|
Protection class |
IP20 |
|
|
Short circuit |
Protection type; auto rest |
|
|
Over voltage |
300Vac, 2H |
|
|
Over temperature |
Protection type; auto rest |
|
|
SAFETY&EMC
|
Safety |
EN61347-1 EN61347-2-13 EN60598-1 EN60598-2-6 |
|
EMC |
EN55015, EN61000-3-2ClassC |
|
|
EN61000-3-3, EN61547 |
||
|
Approvals |
SEMKO, CE, RoHS |
|
|
Withstand voltage |
IN-OUT:3.75KVAC/5mA/1min |
|
|
NOTE |
1, Power factor and efficiency is detected at 230Vac input and full load. 2, Stand-by power is detected at 230Vac input and switch off LED load by push button. |
|
Dimming Operation:
1.Push button switch for dimming (see wiring diagram, Fig A)
- ON/OFF: Short push (120ms ~ 1sec) on the switch
- Stepless dimming: Long push (＞1sec) on the switch. With every other long push, the light level goes the opposite direction.
- Synchronization: No need additional synchrony wire in larger installation, up to 15pcs drivers when connected to the same switch.
2.1-10V dimming (see wiring diagram, Fig B)
The driver supports any active 1-10V dimmer. When the dimming signal is less than 0.8V ~ 1V or short the dimming wires, the output of LED driver could be completely switch off, see Fig B
Wiring Scheme:
Applications:
For downlights in lobby,corridor
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.