Dual row wafer connector with1.0mm pitch PA6T materials, SHD PCB top entry shrouded header
1, Detailed specification of product:
1.Basic information:
- Color: Black
- Pitch: 1.00mm
- Circuits: 12/16/20/30/40/50positions
- Insulation O.D.: 0.80mm
- Pin materials: Phosphor Bronze or gold flash
- Solder tabs: Brass/Gold flash
- Wafer material: Nylon6T,UL94V-0
- Cap:Nylon6T,UL94V-0
- Matched housing: A1001 series dual row
- Mounting type: SMT
- Application: Signal, wire to board
- Terminal materials: Phosphor bronze
- Finish terminal: Tin-plated or gold-flash type
- Terminal Package: 15K pcs/reel
- Terminal processing method: E-stamping before tin-plated
2. Electrical characteristic:
- Current Rating: 1A AC DC
- Voltage Rating: 50V AC, DC
- Contact Resistance: 20mΩ Max
- Insulation Resistance: 100mΩ
- Withstanding Voltage: 500V AC/minute
3. Mechanical characteristic:
- Temperature Range:-25°C ~+85°C
- Terminal Insertion Force: 0.50kgf (Max.)
- Terminal/Housing Retention Force: 0.70kgf (Min.)
- Pin Retention Force: 0.50kgf (Min.)
Other detailed data please check the pictures as below.
2, Introduction for this series products
Please kindly notice these series product, if you can buy this product as a set, the price will be very reasonale and favorable.
1, Terminal:A1001-T-A
2, Housing: Dual housing: A1001H-2XNP
Single housing: A1001H-NP-1 & A1001H-NP-2 & A1001HB-NP-1
3, Wafer: Dual rows type: A1001WV-S-2XNP & A1001WR-S-2XNP & A1001WV-SF-2XNP
Single row type: A1001WV-S-NP & A1001WR-S-NP
A1001 series demo
3,Corresponding engineering drawing & test report
Below file is our engineering drawing and testing report for further information. It's sure that it will be a
good reference for you to know this series parts clearly.
Drawing of dimension
6. Environmental Performance And Others
| Test Description | Procedure | Requirement | |
| 6-1 | Temperature Rise | Carrying rated current load.(Based upon UL 498) | 30℃(Max.) |
| 6-2 | Heat Resistance | 85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) |
Appearance No Damage. Contact Resistance 40mΩ (Max.) |
| 6-3 | Cold Resistance | -25±3℃,96 hours (Based upon JIS C0020) | |
| 6-4 | Humidity |
Temperature: 40±2℃ Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) |
Appearance No Damage. Contact Resistance 40mΩ (Max.) Insulation Resistance 10MΩ (Min.) Dielectric Withstanding Voltage Must meet 4-3 |
| 6-5 | Temperature Cycling |
5 cycles of: a) -55℃ 30 minutes b) +85℃ 30 minutes (Based upon JIS C0025) |
Appearance No Damage. Contact Resistance 40mΩ (Max.) |
| 6-6 | Salt Spray | Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101C Cond. B) | |
| 6-7 | SO2 Gas |
24 hours exposure to 50±5ppm. SO2 gas at 40±2℃. |
|
| 6-8 | NH3 Gas | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | |
| 6-9 | Solderability |
Soldering Time: 5±0.5 sec. Solder Temperature: 245±5℃ |
Solder Wetting 95% of immersed area must show no voids, pin holes |
| 6-10 | Resistance to Soldering Heat |
When reflowing Refer to paragraph 8 Solder iron method Soldering Time: 5±0.5 sec. Solder Temperature: 370℃ ~ 400℃ |
Appearance No Damage. |
7. Actuator Insertion/Withdrawal Force
[Unit : kgf]
| Circuits | At Initial | Circuits | At Initial | ||
| Insertion (Max.) | Withdrawal (Min.) | Insertion (Max.) | Withdrawal (Min.) | ||
| Single | 0.20 | 0.03 | 13 | 4.30 | 1.20 |
| 02 | 1.00 | 0.10 | 14 | 4.60 | 1.30 |
| 03 | 1.30 | 0.20 | 15 | 4.90 | 1.40 |
| 04 | 1.60 | 0.30 | 16 | 5.20 | 1.50 |
| 05 | 1.90 | 0.40 | 17 | 5.50 | 1.60 |
| 06 | 2.20 | 0.50 | 18 | 5.80 | 1.70 |
| 07 | 2.50 | 0.60 | 19 | 6.10 | 1.80 |
| 08 | 2.80 | 0.70 | 20 | 6.40 | 1.90 |
| 09 | 3.10 | 0.80 | 2X15 | 9.40 | 2.90 |
| 10 | 3.40 | 0.90 | 2X20 | 12.40 | 3.90 |
| 11 | 3.70 | 1.00 | 2X25 | 15.40 | 4.90 |
| 12 | 4.00 | 1.10 | |||
3, Our service
1.Quality is life, we establish our brand step by step (high quality).
2.Competitive price.
3.Attractive package.
4.Fast Delivery.
5.Excellent after-sale service.
6.Feel free to join our team and establish business relationship with us.
7.Welcome to inquiry us and send you our catalogue to know what we have.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.