Aluminum Shell 3 Way PDU Power Distribution Unit With Switch Controlled IEC 320 C19
IEC 320 C19 3 Way Outlet Hardwired Power Strip with Switch Controlled PDU Power Distribution Unit
Product Information
Supply Voltage VAC: 125V OR 250V
Output Outlet Type: IEC 60320 C19
Inlet Outlet Type: IEC 60320 C20
Product Range: 15A 125VAC; 10A 250VAC
Cable Length: -
No. of Outlets: 3Outlets
Current Rating: 15A OR 10A
Product Overview
The SFC-IEC-03 is a 15A or 10A 3-outlet gray plug-in Power Strip with IEC connector. This International power strip provides power safely and conveniently to use. The input is provided with a male IEC320 receptacle, outputs are provided with a female IEC320 receptacle. It is ideal for use in a wide variety of settings, including relay racks and cabinets, laboratories, workshops, classrooms and offices.
. User-ready outlets
. Single-pole circuit breaker with switch
. 1.2 to 9.5" Center-to-centre receptacle
. Rugged construction
. Space saving
. Low profile
. Snap-on, slide-off mounting
Applications
Power Management, Safety UL C-UL List. E 491513
Footnotes
Appropriate input cord is not included.
| Specification |
| Model #: | SFC-IEC-03 |
| Description: | 5 to 14" 3 Outlet Hardwired Power Strip |
| Power Strip Measurement: | L5 to14" x W1.614" x H1.255" (133 to 355 x 45 x 42) * |
| Outlets: | 3 |
| Outlet Color: | Black, white, grey or other |
| Outlet Orientation: | Vertical or level |
| Receptacle Type: | IEC60320 C19 |
| Outlet Spacing: | 0.12to 8.39" (3 to 213mm) (center to center) |
| IEC C20 Inlet: | on front of strip |
| Voltage Input/Output: | 110-125V 60Hz |
| Current Input: | 15A |
| Full Load: | 1875VA |
| On/Off Switch: | Yes |
| Circuit Breaker: | NO |
| Surge Protection: | NO |
| Indicators: | NO |
| Mounting Tabs: | On both ends or bottom |
| Mounting Clips: | Mounting Clips included |
INSTALLATION GUIDE:
Before installation, you may need to get a IEC C19 Outlet. Decide your wire gauge, and ask store attendant for assistance what color of connectors you should get) from your local hardware or electric supply or home improvement stores.
Minimum tools required: A fine to medium fine philips screw driver, and a pair of scissors, and a pair of mid size slip joint pliers
1. Turn off electricity in the house
2. Decide where to place this unit
3. Choose the side you want the cord exit to choose IEC C20 Built in power strips
4. Match the color of the wires and secure the wire connection with proper wire connectors built in IEC C19 plug.(different wire gauge use different colored wire connectors)
- Mount the power strip where you want it to be:
A) For power strips with mounting tabs on both ends: screw down the unit on the floor, wall or in your cabinet or on your rack, where you want it to be
B) For power strips without mounting tabs, but to be mounted with clips, place the unit where you want it to be first, make marks where to install the clips, which normally should be placed about min 2”<power strips length away from each end, and then screw the clips down with screws provided. Then, snap the power strip in on the clips - Push IEC C19 outlet plug into IEC C20 inlet power strips , and push switch to ON. Turn electricity back on, you are ready to go.
Note:
We also custom manufacture for our customers.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.