Single Mode SFP Fiber Optic Transceiver Module Hot Pluggable XFP Footprint
10G XFP Single Mode 1310nm 10km SFP Optical Transceiver Module
Features
- Supports 9.95Gb/s to 11.1Gb/s bit rates
- Hot-pluggable XFP footprint
- Maximum link length of 10km with SMF
- 1310nm uncooled DFB laser
- XFP MSA package with duplex LC connector
- No reference clock required
- +1.8V,+3.3V Supply Voltage
- XFI and lineside loopback Mode Supported
- -5ºC to 70ºC Operating Case Temperature
- Diagnostic Performance Monitoring of module temperature,Supply Voltages, laser bias current, transmit optical power, and receive optical power
- RoHS6 compliant (lead free)
Applications
- 10GBASE-LR at 10.3125Gbps
- Other optical links,up to 11.1Gbps
Description
E-link LNK-XFP-10G-LR is compliant with the 10G Small Form-Factor Pluggable (XFP) Multi-Source Agreement (MSA), supporting data-rate of 10.3125Gbps(10GBASE-LR) or 9.953Gbps 10GBASE-LW), and transmission distance up to 10km on SMF.
The transceiver module comprises a transmitter with 1310nm Uncooled DFB laser and a receiver with a PIN photodiode. Transmitter and receiver are separate within a wide temperature range of 0℃ to +70℃ and offers optimum heat dissipation and excellent electromagnetic shielding thus enabling high port densities for 10G systems.
Absolute Maximum Ratings
| Parameter | Symbol | Min | Max | Unit |
| Supply Voltage3 | Vcc1 | -0.5 | 4.0 | V |
| Supply Voltage 2 | Vcc2 | -0.5 | 2 | V |
| Storage Temperature | Tst | -40 | 85 | ºC |
| Case Operating Temperature | Top | -5 | 70 | ºC |
Electrical Characteristics
| Parameter | Symbol | Min | Typ | Max | Unit | Note | |
| Operating Case Temperature Range | Tc | 0 | +70 | ℃ | |||
| Power Supply Voltage @ 3.3V | Vcc3 | 3.13 | 3.3 | 3.47 | V | ||
| Module total power | P | 2.5 | W | ||||
| Transmitter | |||||||
| Input differential impedance | Rin | 100 | Ω | 1 | |||
| Differential data input swing | Vin,pp | 120 | 820 | mV | |||
| Transmit Disable Voltage | VD | 2.0 | Vcc | V | |||
| Transmit Enable Voltage | VEN | GND | GND+0.8 | V | |||
| Transmit Disable Assert Time | 10 | us | |||||
| Receiver | |||||||
| Differential data output swing | Vout,pp | 500 | 850 | mV | |||
| Data output rise time | tr | 40 | ps | 2 | |||
| Data output fall time | tf | 40 | ps | 2 | |||
| LOS Fault | VLOS fault | Vcc - 0.5 | VccHOST | V | 3 | ||
| LOS Normal | VLOS norm | GND | GND+0.5 | V | 3 | ||
| Power Supply Rejection | PSR | See Note 3 below | 4 | ||||
Notes:
1. After internal AC coupling.
2. 20 – 80 %
3. Loss Of Signal is open collector to be pulled up with a 4.7k – 10kohm resistor to 3.15 – 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
4. Per Section 2.7.1. in the XFP MSA Specification.
Optical Characteristics
| Parameter | Symbol | Min | Typ | Max | Unit | Ref. |
| Transmitter | ||||||
| Optical output Power | P | -6.5 | +0.5 | dBm | ||
| Optical Wavelength | λ | 1260 | 1355 | nm | ||
| Optical Extinction Ratio | ER | 6 | dB | 1 | ||
| Side Mode Suppression Ratio | SMSR | 30 | dB | |||
| Average Launch power of OFF transmitter | POFF | -30 | dBm | |||
| Tx Jitter | Txj | Compliant with each standard requirements | ||||
| Receiver | ||||||
| Receiver Sensitivity | RSENS | -15 | dBm | 2 | ||
| Receiver Sensitivity in OMA | RSENS | -12.5 | dBm | 2 | ||
| Maximum Input Power | PMAX | +0.5 | dBm | |||
| Optical Center Wavelength | λC | 1260 | 1600 | nm | ||
| LOS De-Assert | LOSD | -15 | dBm | |||
| LOS Assert | LOSA | -25 | dBm | |||
| LOS Hysteresis | 1 | 4 | dB | |||
Notes:
1, PRBS 231-1 test pattern @10.3125Gbps.
2, PRBS 231-1 test pattern @10.3125Gbps, BER≤10-12.
Pin Descriptions
| Pin | Logic | Symbol | Name/Description | Ref |
| 1 | GND | Module Ground | 1 | |
| 2 | VEE5 | Optional –5.2 Power Supply – Not required | ||
| 3 | LVTTL-I | Mod-Desel | Module De-select; When held low allows the module to , respond to 2-wire serial interface commands | |
| 4 | LVTTL-O | Interrupt | Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface | 2 |
| 5 | LVTTL-I | TX_DIS | Transmitter Disable; Transmitter laser source turned off | |
| 6 | VCC5 | +5 Power Supply – Not required | ||
| 7 | GND | Module Ground | 1 | |
| 8 | VCC3 | +3.3V Power Supply | ||
| 9 | VCC3 | +3.3V Power Supply | ||
| 10 | LVTTL-I | SCL | Serial 2-wire interface clock | 2 |
| 11 | LVTTL- I/O | SDA | Serial 2-wire interface data line | 2 |
| 12 | LVTTL-O | Mod_Abs | Module Absent; Indicates module is not present. Grounded in the module. | 2 |
| 13 | LVTTL-O | Mod_NR | Module Not Ready; | 2 |
| 14 | LVTTL-O | RX_LOS | Receiver Loss of Signal indicator | 2 |
| 15 | GND | Module Ground | 1 | |
| 16 | GND | Module Ground | 1 | |
| 17 | CML-O | RD- | Receiver inverted data output | |
| 18 | CML-O | RD+ | Receiver non-inverted data output | |
| 19 | GND | Module Ground | 1 | |
| 20 | VCC2 | +1.8V Power Supply | ||
| 21 | LVTTL-I | P_Down/RST | Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset | |
| Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. | ||||
| 22 | VCC2 | +1.8V Power Supply | ||
| 23 | GND | Module Ground | 1 | |
| 24 | PECL-I | RefCLK+ | Reference Clock non-inverted input, AC coupled on the host board – Not required | 3 |
| 25 | PECL-I | RefCLK- | Reference Clock inverted input, AC coupled on the host board – Not required | 3 |
| 26 | GND | Module Ground | 1 | |
| 27 | GND | Module Ground | 1 | |
| 28 | CML-I | TD- | Transmitter inverted data input | |
| 29 | CML-I | TD+ | Transmitter non-inverted data input | |
| 30 | GND | Module Ground | 1 |
Notes:
1. Module circuit ground is isolated from module chassis ground within the module.
2. Open collector; should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.15Vand 3.6V.
3. A Reference Clock input is not required.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.