Pentype VFL Optical Fiber Visual Fault locator 40MW For End-to-End Visual Fiber Identification Fiber Testing Tools
Pentype VFL Optical Fiber Visual Fault locator 40MW For End-to-End Visual Fiber Identification Fiber Testing Tools
Method of use
1. Screw the end cap from the pen, the battery will be prepared into the pen, battery cathode to the end cap, the positive on the pen body is positive;(note: please do not turn pen and pencil tail into the battery)
2. Put the pen and pencil body connection installed, open the dust cap, press the control switch one time, observe the interface has a red light, luminous tube on at the same time;(note don't eyes were light interface, so as not to damage the eye)
3. Press the control switch again, observe the light into a pulse mode, the indicator light-emitting tube and out of sync pulse light;(pulse frequency in 2-3 hz or 9 hz)
4. Press the control switch again, light source closed, no light output, at the same time indicator light pipe out;(switch mode to: continuous - pulse - closed - continuous cycle mode)
5. When detecting insert tested optical fiber optical interface, press the control switch at the same time, choose the output light work mode (continuous or pulse);
6. After use, build the dust cap, do not use for a long time, please take out the battery, in order to avoid battery rot, damage the light source.
Features
1.adopt high quality triangular laser chip, life 8000-8000 hours
2.Use APC circuit, constant power output and battery pack design
3.Low power LED display, display more intuitive
4.Is normally on, flash (9 hz), slow flash (3 hz) three work modes
5.overall style resembles transformers, hale, devices are strong
6.Shell parts for aluminum alloy material, the surface anodic oxidation bright black, buttons for stainless steel 316, grain surface car light
7.Products increase the heatsink, multiple electrostatic protection, power is more stable
8.2.5mm universal connector,for 1.25mm connectors,FC(male)-LC(Female) adaptor also can be provided on request
9.Operates either in CW or Pulsed mode with constant output power
10.Long battery life (up to 60 hours)
11.Drop-resistant and dust-proof design of laser head
12.Laser case ground design prevents ESD damage
13.Portable and rugged
14.Easy to use
Maintenance and matters needing attention
3. The work of laser optical fiber head should be cleaned;
4. When used, the optical interface and the interface needs to detect light and light pull plug;
5. Don't use the light source, would you please put dust cap to avoid dust fall;
6. Should remove the battery when not in using;
7. Please do not remove the end cap and any part of the dust cap, remove shall not be responsible for damage caused.Fiber Checker Fiber Tester Tools Optic Visual Fault Detector network fiber checker fiber optic visual fault detector
| Model | HCW-8S | |||||
| Central wavelength | 650nm±10nm (635nm is available on request) | |||||
| Emitter type | FP-LD | |||||
| Output power | 5mw | 10mw | 20mw | 30mw | 40mw | 50mw |
| Laser Range | ≥5km | ≥10km | ≥20km | ≥30km | >35km | >40km |
| Pulse frequency | 2Hz to 3Hz / 9Hz | |||||
| Power supply | 2AA alkaline batteries | |||||
| Operating temperature | -20°C to 60°C | |||||
| Storage temperature | -40°C to 85°C | |||||
| Dimension | 22*3.5*2.6cm | |||||
| Weight | 155g (without battery) | |||||
| Operating model | Both CW and Pulse available | |||||
| Optical connector | 2.5mm universal connector, for 1.25mm connectors, FC (Male)-LC. (Female) convertor can be provided on request | |||||
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.