|
ICE CREAM Refrigerated Truck Box
|
|
|
|
|||
|
Ice Cream Refrigerated Truck Body
Made by FRP Insulated Sandwich Panels with Eutectic Plates Refrigeration Units
for Ice Cream Deep Sea Fish and Ultralow temperature Controled Vaccine
|
|
|
|
|||
|
1. MODEL:
|
|
|
GET.6KDX.XIC.
|
|||
|
Ice cream (derived from earlier cream ice) is a sweetened frozen food typically eaten as a snack or dessert. It may be made from dairy milk or cream and is flavoured with a sweetener, either sugar or an alternative, and a spice, such as cocoa or vanilla, or with fruit such as strawberries or peaches. It can also be made by whisking a flavored cream base and liquid nitrogen tog. Colorings are sometimes added, in addition to stabilizers. The mixture is cooled below the freezing point of water and stirred to incorporate air spaces and to prevent detectable ice crystals from forming. The result is a smooth, semi-solid foam that is solid at very low temperatures (below 2 °C or 35 °F). It becomes more malleable as its temperature increases.
its transport temperature asked a super Lower Temperature Under -18°C ~ -30 °C , the best is the Eutectic plates , if it is packed with bottles ,the Air refrigeration system is also acceptable. |
|
|
|
|||
|
3. GENERAL PARAMETERS
|
|
|
|
|||
|
K .Value for the Composite Box
|
|
0.295 W/㎡ ℃
|
|
|||
|
Max. Overall Length
|
48 ft
|
14,750 mm
|
0~14750mm can choose
|
|||
|
Max. Overall Width
|
10 ft
|
3,200 mm
|
0~ 3200 mm can choose
|
|||
|
Max. Overall Height
|
10 ft
|
3,200 mm
|
0~3200 mm can choose
|
|||
|
Max. Floor Thinckness
|
4 .13 inch
|
105 mm
|
45-105mm can choose
|
|||
|
Side Wall Thickness
|
4 .13 inch
|
105 mm
|
45-105mm can choose
|
|||
|
Front Wall Thickness
|
4 .13 inch
|
105 mm
|
45-105mm can choose
|
|||
|
Rear Door Panel
|
4 .13 inch
|
105 mm
|
45-105mm can choose
|
|||
|
Roof Wall
|
4 .92 inch
|
125 mm
|
45-105mm can choose
|
|||
|
4. Box Structure
|
|
|
|
|||
|
super Structure
|
self-supporting body, without cross bars , inside and outside skin made of glass fibre reinforced polyester, reinforced with
Z-Straps , the Core of hard foam with best insulation properties. Without metallic carrier elements = without direct heat conductivity The body are water tight the plastic elements are flam resistant |
|
|
|||
|
Rear Wall
|
Three -wing Rear door , approx ,80 mm thick with 5-fold special sealing ,rigid frame joints.
Each Door Wing with 1 external power-brace lock with one -hand operation Door Wings inclinable to the sidewalls with hold-open device (loose) |
|
|
|||
|
Portal
|
stainless Steel
|
|
|
|||
|
Surface
|
The Plastic elements are painted white, White gelcoat colour both side, uv resistant, food grade approval
|
|
|
|||
|
Refrigeration units
|
Manufacturer : thermoking or Carrier,
Refrigeration unit type : Engine Powered, Diesel Powered , Full- Electric Units; standby can Customize Refrigeratant : R404 |
|
|
||
|
Temperature sensor
|
Temperature sensors for medicine
two constant monitoring sensors, with the led interface panel in driver’s room for continuous monitoring of temperature, equipped with an alarm system. |
|
|
||
|
|
Temperature sensors for normal carogs:
one constant monitoring sensors, with the led interface panel in driver’s room for continuous monitoring of temperature, equipped with an alarm system. |
|
|
||
|
|
|
|
|
||
|
It is very easy to assemble our insulated bodies, because applying polyurethane adhesive to the joint area of the FRP-Pie Panel Kits sandwich panels, which ensures the joint reliability and optimum insulation, forms them. All bodies ckd we provide have included all necessary accessories such as aluminum angles, aluminum corner, sealing glues, screws, side guards, etc. Therefore, you can assemble them by yourself without purchasing any material. Generally, 3-4 workers can assemble 5-6 bodies everyday.
Moreover, at the beginning we will assign our engineers to supply you some technical guidance.
|
|
|
|
|||
|
CKD Panel Kits
|
1. Prepare the chassis
2. Mount the partial Sub-Chassis and the floor plate on the chassis with Supplied U bolts and other parts 3. Mount the side, front and the roof and the Rear Door Portal and the door with Glues approx.1.5 hours, with a set time At Least 8 h at +20 ℃ . 4. Install the required options 5. Finishing |
|
|
|||
|
CBU Box
|
1.Prepare the chassis
2. Mount the BOX tog with subframes on the chassis 3. Install the required options 4. Finishing |
|
|
|||
|
|
|
|
|
|||
Have questions about our products or want to discuss a custom order? Our team is ready to help you.