Tube Connector Medical Grade Platinum Cured Silicone Rapid Vulcanization
Medical Grade Platinum Cured Silicone Surgical Grade Silicone Rubber Pure For Tube Connector
Typical Properties
|
LSR M 6250-30YH |
|||
|
Properties |
Unit |
A |
B |
|
Appearance |
/ |
transparent |
transparent |
|
Viscosity |
mPa.s |
1200000 - 1800000 |
|
|
Density |
g/cm3 |
1.1 ± 0.02 |
|
|
Shore A Hardness |
A/JLS |
30 ± 2 |
|
|
Tensile Strength |
MPa |
≥ 7.0 |
|
|
Elongation at break |
% |
≥ 650 |
|
|
Tear Strength |
KN/m |
≥ 15 |
|
|
Linear Shrinkage |
% |
≤ 0.1 |
|
|
Tensile set |
% |
≥ 2.6 |
|
|
Rebound |
% |
≥ 45 |
|
|
Compression set |
(22 hrs at 175℃) % |
≤ 30 |
|
These figures are for reference only, please contact us for details.
Operation ways of Injection Molding
1, mixed: A component (based glue) and Part B (curing agent) ratio of 10:1 or 1:1 by weight, mixed, mixed either manually or using equipment.
2, vacuuming: mixed silicone A and B, When used in small amounts can be in a vacuum desiccator under vacuum, the volume will foamed plastic material can be increased 4-5 times, so degassing vessel volume should be less than bulky plastic material 4 to 5 times, after a few minutes gel volume returns to normal, no air bubbles escaping when the surface (about 10 minutes) to complete the degassing step.
3, clean your Original mold (sex toys molds), please note that the molds won’t contact with condensation silicone rubber before, and not contains a chemical element such as N.S.P, otherwise, the silicone won’t be cured.
5. cured the silicone rubber at 90℃ to 150℃, then the silicone will be cured, and then demould.
Key Features and Benefits
- Rapid vulcanization
- Sensational weather resistance
- Sensational weather resistance
- Excellent resistance to acid and alkali
- High stability to ozone and ultraviolet light
- High thermal stability
- Sterilizable with ethylene oxide, steam and gamma radiation
- Excellent biocompatibility
Certificates
Rui-He silicone rubber obtained the following test certificate: RoHS, FDA, MSDS, LFGB, ISO9001:2016.
Packaging & Storage
|
Packaging Details |
This kind of rubber is packed in 20kg/plastic barrels or 200KG/iron drum with an inside plastic bag. |
|
|
Port |
HUANGPU, GUANGZHOU |
|
|
Lead Time |
1 – 1000 (Kilograms) |
7 days |
Store in a cool dry place out of direct sunlight, use it within 12 months from the day of manufacture.
Production Process
-
Add raw material
-
Stir and mix
-
Sampling inspection
-
(Viscosity detection, Hardness test, Tear resistance)
-
Mass production
-
Label
-
Packing
-
Transport
Instructions
1. LSR A + B components typically come in a 5-gallon pail or 55-gallon drum. A process controlled pumping kit presses down on the buckets to force the material into the static mixer and feed into the injection unit.
2. Then, streams of pigment can be added and controlled. In the injection, press material will be mixed together additionally with a screw and pushed forward to create a “shot” of material, or the amount needed to fill the mold.
3. After the material is injected into the mold, it will then stay clamped together to cure the LSR. Then, either an operator or a robot will remove the cured product from the mold and the cycle repeats. It is a very quick efficient process that typically averages 30 seconds.
Notice
This product cannot be contacted with compounds containing N, P, S to avoid affecting the catalytic effect of platinum.
If you need to know the prices of our silicone rubbers, please contact us. We do not provide prices on the website because prices fluctuate for many reasons.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.