3Hp Plastic Swimming Pool Water Pump High Pressure IP55 Waterproof Standard
3Hp Plastic Outside Pool Swimming Pool Water Pump Swimming Pool Pump 3hp
| Model | Voltage | HZ | Power(KW) | Power(HP) | Hmax(m) | Qmax(m³/h) | Port Size(inch/mm) |
| FL-150 | 220V-240V | 50/60 | 1.1 | 1.5 | 18 | 30 | 2.0/63 |
| FL-200 | 220V-240V | 50/60 | 1.5 | 2 | 19 | 35 | 2.0/63 |
| FL-300 | 220V-240V | 50/60 | 2.2 | 3 | 20 | 38 | 2.0/63 |
| FL-350 | 220V-240V | 50/60 | 2.6 | 3.5 | 21 | 40 | 2.0/63 |
| FL-400 | 380V | 50/60 | 3 | 4 | 22 | 48 | 2.0/63 |
Features:
1) Magnificent flow rate and lift, the core energy of water circulating, 2~3m suction lift
2) Engineering plastic body, the pump can be effectively protected under bad weather,long service life;
3) Seiko manufacturing, low noise during the pump working time;
4) Free-tool filter cover design, easy to maintenance;
5) IP55 protection level, with None-leaky design;
6) German technology IBC bearing, 100% copper wire motor, 24 hours running.
7) Anti-rust cast-aluminum motor cover, fast heat dissipation; PPO plastic steel material impeller, resist high temperature and corrosion
8) Silicone sealing ring cover all watering section, enhance pump sealing system
9) CE certificated, reliable and safety
Description:
INSTALLATION
Only qualified licensed electrician should install pump and wiring.
IMPORTANT ELECTRICAL
Electrical Contractors Please Note: All 220/380 Volt 50Hz pumps must be wired to the main power
supply through an approved and correctly rated electrician.
PUMP MOUNT MUST
Ÿ Be solid Level Rigid Vibration Free.
Ÿ Allow use of short, direct suction pipe. (To reduce friction losses & don’t install the pump more
than 3M geometrical height from water level)
Ÿ Allow for gate valves in suction and discharge piping.
Ÿ Have adequate floor drainage to prevent flooding.
Ÿ Be protected from excess moisture.
Ÿ All adequate access for servicing pump and piping.
NOTICE
Pump suction and discharge connections have moulded in thread stops, DO NOT try to screw pipe
in beyond these stops.
OPERATION
NEVER run pump dry! Running pump dry may damage seals, causing leakage and flooding! Fill
pump with water before starting motor.
Before removing lid:
STOP PUMP before proceeding.
CLOSE GATE VALVES in suction and discharge pipes.
RELEASE ALL PRESSURE from pump and piping system.
NEVER tighten or loosen screw while pump is operation.
PERFORMANCE: This Pool Pump takes care of cleaning, filtration and chlorine/salt distribution. features a removable strainer basket with a built-in thermal overload protection as the water circulates and passes through the filter leaves your pool clean.
Factory Introduction
FREESEA group has been engaged in pool filtration industry for more than 15 years. Mainly produce pool filtration equipment: Sand filter, circulation pump, vaccum air blower, etc. It is located in Ningbo city Zhoushan island, we provide OEM service for many famous pool brand in foreign & domestic market. Pumps annual output more than 20 thousands. We accept different standard(USA, EU, CN etc).Has many branches in China main city and Spain, sales network extend to all over the world.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.