Resmed Lumis 150 Vpap St Non Invasive Ventilation Machine Customized Color
Lumis 150 ST is a non invasive ventilator designed for non dependent patients with respiratory insufficiency. Featuring ResMed's unique volume assurance mode - iVAPS (intelligent Volume Assured Pressure Support) - Lumis 150 VPAP ST maintains target alveolar ventilation to suit each patient's changing needs. Optional AutoEPAP ensures adequate EPAP is delivered to maintain an open upper airway - automatically, while an intelligent Backup Rate (iBR) encourages spontaneous breathing. Lumis 150 ST is also easy to set up and use.
Key Features
-
iVAPS
-
intelligent Backup Rate (iBR)
-
AutoEPAP maintains upper airway patency
-
Vsync
-
TiControl
-
5 Trigger and Cycle Senstivities
-
QuickNav for low touch therapy adjustments
-
Climate Control Auto for automatic humidification
-
Ramp and Rampdown for extra comfort.
-
supported by ResScan 5.4
Specifications
|
Height |
150 mm |
|---|---|
|
Weight |
1268 gm |
|
Breadth |
255 mm |
|
Length |
116 mm |
|
Sound pressure level |
27 dBA with uncertainty of 2 dBA |
|
Standard air filter |
Material: Polyester non woven fibre Average arrestance: >75% for ~7 micron dust |
|
Aircraft use |
ResMed confirms that device meets the Federal Aviation Administration (FAA) requirements (RTCA/DO-160, section 21, category M) for all phases of air travel. |
|
Modes |
CPAP, S, T, ST with optional iBR, PAC, iVAPS with iBR and optional Auto EPAP |
|
Water capacity |
To maximum fill line 380 mL |
|
Sensors |
Pressure sensor: Internally located at device outlet, analogue gauge pressure type, -5 to +45 cm H2O (-5 to +45 hPa) Flow sensor: Internally located at device inlet, digital mass flow type, -70 to +180 L/min |
|
Maximum single fault steady pressure |
Device will shut down in the presence of a single fault if the steady state pressure exceeds: 30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec. |
|
Housing construction |
Flame retardant engineering thermoplastic |
|
Cleanable humidifier |
material: Injection moulded plastic, stainless steel and silicone seal |
|
Operating pressure range |
S, ST, T, PAC, iVAPS: 2 to 25 cm H2O (2 to 25 hPa) CPAP 4 to 20 cm H2O (4 to 20 hPa) |
|
Operating temperature/ humidity/altitude |
+5°C to +35°C / 10 to 95% relative humidity, non-condensing / Sea level to 8,500' (2,591 m); air pressure range 1013 hPa to 738 hPa |
|
Storage and transport temperature/humidity |
-20°C to +60°C / 5 to 95% relative humidity, non-condensing |
|
Supplemental oxygen |
Maximum flow: 15 L/min (S, ST, T, PAC, CPAP), 4 L/min (iVAPS) |
|
Air outlet |
(complies with ISO 5356-1:2004): 22 mm |
|
Electromagnetic compatibility |
requirements (EMC) according to IEC 60601-1-2:2014, for residential, commercial and light industry environments. It is recommended that mobile communication devices are kept at least 1 m away from the device. |
|
IEC 60601-1:2005+A1:2012 classification |
Class II (double insulation), Type BF, Ingress protection IP22 |
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.