Industrial Spray Pump for Drilling Mud Systems - 7.5-20 m³/h Flow, 10-14m Head with 48-53% Efficiency
Price:
Negotiable
MOQ:
1sets
Delivery Time:
30days
Brand:
ATO
Product Description
Industrial Spray Pump for Drilling Mud Systems
This specialized spray pump is engineered specifically for oil drilling mud pumps, providing essential flushing and cooling functions for sleeves and pistons during pump operation, as well as mud transportation capabilities.
Technical Specifications
| Model | Flow (m³/h) | Head (m) | Efficiency (%) | Speed (r/min) | Shaft Power (kW) | Motor Power (kW) |
|---|---|---|---|---|---|---|
| 32SB180J-2.2 | 7.5 | 10 | 48 | 1420 | 0.55 | 2.2 |
| 32SB180J-4 | 9 | 14 | 48 | 1440 | 0.72 | 4 |
| 32SB180J-5.5 | 9 | 14 | 48 | 1440 | 0.72 | 5.5 |
| 32PL | 7.5 | 10 | 48 | 1420 | 0.43 | - |
| 40SB180J-3 | 15 | 10 | 53 | 1420 | 0.77 | 3 |
| 40SB180J-4 | 20 | 10 | 53 | 1440 | 1.0 | 4 |
Structural Design
The spray pump consists of pump body, mechanically sealed pump cover, mechanical seal, impeller, and pump base. Key structural advantages include:
- Mechanical sealing system ensures leak-free operation
- Dual drive options: motor direct drive and pulley drive
Component Identification: 1.Pump body 2.Cap nut 3.Washer 4.Impeller 5.Pump cover 6.Mechanical seal 7.Machine sealing gland 8.Oil seal 9.Bearing cover 10.Shaft 11.Nameplate 12.Bearing 13.Pump base
Installation Guidelines
Pump Placement
- Install near pumping source to minimize suction length and loss
- Ensure horizontal, firm, and vibration-resistant mounting
Drive System Alignment
- Shaft coupling alignment: parallel offset ≤ 0.25mm, corner error ≤ 0.12mm
- Pulley drive: parallel axes with ≤ 2mm end error
Pipeline Configuration
- Inlet pipeline area must equal or exceed pump inlet area
- Use gradual transitions to prevent air bubbles in suction lines
- Install support for all pipelines - pump must not bear pipeline weight
Operation & Maintenance
Startup Procedure
- Manually rotate pump shaft to ensure smooth operation
- Fill pump body and inlet pipeline with fluid to remove air
- No-load running time must not exceed 5 seconds
Lubrication Schedule
- Use universal lithium-based grease for bearings
- Replace grease every 1500 operating hours
Troubleshooting Guide
| Fault | Cause | Solution |
|---|---|---|
| Excessive shaft power | Impeller friction or operation below design lift | Adjust clearances or throttle outlet valve |
| Reduced lift and flow | Blockages, low speed, worn impeller, or excessive clearance | Clear obstructions, check speed, replace impeller, adjust clearances |
| Bearing overheating | Contaminated lubricant or worn bearings | Replace lubricant or bearings |
| Vibration and noise | Unbalanced impeller, worn bearings, loose connections, or cavitation | Replace components, tighten connections, improve suction conditions |
| Sealing leakage | Foreign substances, improper installation, or worn seals | Clean, reinstall, or replace mechanical seals |
Note: These pumps are designed for operation within specified design parameters only.
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
XIAN ATO INTERNATIONAL CO.,LTD
Location
Building 15+, No. 2, Biyuan 3rd Road, High-tech Zone, Xi 'an Post code：710117
Contact Person
Rita Zheng