High Performance 128 Channel Fiber Optic Switch 1xN Passive 1310 / 1550nm
◇ features
- More Than 128 Channels
- ·Low Loss and High Reliability
- ·Parallel Interface (TTL)
- ·Modularized Design
- ·Epoxy-free on Optical Path
◇ Application:
- ·Ring Network
- ·Remote Monitoring in Optical Network
- ·Testing of Fiber, Optical Component
description
1×N Optical switch is a kind of functional component, with the ability of switching optical route. In optical fiber transmission system, it is used for multi-channel fiber monitoring, multi light source detector selection, and optical fiber path protection etc. Besides, it is also used in optical fiber test system for optical fiber and its component test, outdoor cable test and multi-spot optical sensors monitoring system.
◇specification
| Parameters | Unit | GP-OSW1×N | |||
| Insertion Loss | dB | 1<N≤32 | 32 <N≤64 | 64 <N≤128 | |
| Type:0.8 Max:1.0 | Type:0.8Max:1.2 | Type:0.8Max:1.3 | |||
| Wavelength Range | nm | 850±40 /1300±40,1550MM | 1260~1650SM | ||
| Test Wavelength | nm | 850/ 1300,1550MM | 1310/1550SM | ||
| Return Loss | dB | MM≥30SM≥50 | |||
| Crosstalk | dB | ≥70 | |||
| PDL | dB | ≤0.05 | |||
| WDL | dB | ≤0.25 | |||
| TDL | dB | ≤0.25 | |||
| ER (PM swtich) | dB | ≥16 (PoIarization Maintaining switch) | |||
| Repeatability | dB | ≤±0.05 | |||
| Durability | Cycles | ≥10 Million | |||
| SwitchingTime | ms | ≤10(Sequence switch time of adjacent channel) | |||
| OpticalPower | mW | ≤500 | |||
| OperatingTemperature | ℃ | -5~+70 | |||
| Storage Temperature | ℃ | -40~+85 | |||
| Relative Humidity | % | 5 ~95 | |||
| Dimension | mm | 135×40×32(N≤12) | 135×60×32(N≤18) | 135×60×38(N≤32) | |
| 150×80×67(N≤64) | 165×100×100(N≤98) | 185×130×130(N≤128) | |||
◇DB-15 male connector (max.1×64)
(max.1×128)
| Pin No. | Signal Name | I / O | Description |
| 2 | D0 | Input | TTL, Channel selection bit 0 |
| 3 | D1 | Input | TTL, Channel selection bit 1 |
| 4 | D2 | Input | TTL, Channel selection bit 2 |
| 5 | D3 | Input | TTL, Channel selection bit 3 |
| 6 | D4 | Input | TTL, Channel selection bit 4 |
| 10 | D5 | Input | TTL, Channel selection bit 5 |
| 11 | /RESET | Input | TTL, Low level reset to channel 0. High level means channel selection bits are effective. |
| 7 | /READY | Output | TTL, Ready (High=Not ready, Low=Ready) |
| 8 | ERROR | Output | TTL, Error (High=Error, Low=No error) |
| 1, 9 | GND | Input | Ground |
| 15 | +5VDC | Input | 5.0±5% VDC Digitalpower supply(max 50mA) |
| 12 | VM | Input | 5.0±5% VDC or 12±5% VDC Drive power supply(max 800mA) |
| 14 | ISP | Input | TTL, Forinternal firmware upgrade of the module, in the normal mode, please suspended thepin; In the upgrade mode, please send the pin to ground. |
| 13 | NA |
| Pin No. | Signal Name | I / O | Description |
| 2 | D0 | Input | TTL, Channel selection bit 0 |
| 3 | D1 | Input | TTL, Channel selection bit 1 |
| 4 | D2 | Input | TTL, Channel selection bit 2 |
| 5 | D3 | Input | TTL, Channel selection bit 3 |
| 6 | D4 | Input | TTL, Channel selection bit 4 |
| 10 | D5 | Input | TTL, Channel selection bit 5 |
| 13 | D6 | Input | TTL, Channel selection bit 6 |
| 11 | /RESET | Input | TTL, Low level reset to channel 0. High level means channel selection bits are effective. |
| 7 | /READY | Output | TTL, Ready (High=Not ready, Low=Ready) |
| 8 | ERROR | Output | TTL, Error (High=Error, Low=No error) |
| 1, 9 | GND | Input | Ground |
| 15 | +5VDC | Input | 5.0±5% VDC Digitalpower supply(max 50mA) |
| 12 | VM | Input | 5.0±5% VDC or 12±5% VDC Drive power supply(max 800mA) |
| 14 | ISP | Input | TTL, Forinternal firmware upgrade of the module, in the normal mode, please suspended thepin; In the upgrade mode, please send the pin to ground |
◇optical route
| Pin No. | Signal Name | I / O | Description |
| 2 | D0 | Input | TTL, Channel selection bit 0 |
| 3 | D1 | Input | TTL, Channel selection bit 1 |
| 4 | D2 | Input | TTL, Channel selection bit 2 |
| 5 | D3 | Input | TTL, Channel selection bit 3 |
| 6 | D4 | Input | TTL, Channel selection bit 4 |
| 10 | D5 | Input | TTL, Channel selection bit 5 |
| 13 | D6 | Input | TTL, Channel selection bit 6 |
| 11 | /RESET | Input | TTL, Low level reset to channel 0. High level means channel selection bits are effective. |
| 7 | /READY | Output | TTL, Ready (High=Not ready, Low=Ready) |
| 8 | ERROR | Output | TTL, Error (High=Error, Low=No error) |
| 1, 9 | GND | Input | Ground |
| 15 | +5VDC | Input | 5.0±5% VDC Digitalpower supply(max 50mA) |
| 12 | VM | Input | 5.0±5% VDC or 12±5% VDC Drive power supply(max 800mA) |
| 14 | ISP | Input | TTL, Forinternal firmware upgrade of the module, in the normal mode, please suspended thepin; In the upgrade mode, please send the pin to ground. |
company profile
We are specialized in providing solutions for optical cable, packaging solutions for optical devices, and manufacturing of other electronic equipment parts. Our products are widely used in optical communication, electronics, medical care, oil pipeline, audio industrial control, radio, instrumentation and other industries.We have a good design and production team to provide customers with high-quality, reliable and efficient products.
In the process of cooperation, our innovation and service awareness are well received by our customers.
The company specializes in the production of optical communication equipment, optical devices, optical jumpers, distribution boxes, distribution frame.Our company
1.Machinery department: provide precision machinery processing, sheet metal parts processing, plastic injection molding processing, processing and manufacturing supporting various parts.
2. Optical communication department: provide customized processing of optical devices such as optical jumper, optical module, optical switch, wave divider, attenuator adapter, coupler, optical splitter, circulator, isolator, collimator, optical amplifier, etc.
FAQ
Q:Can you design and customize production according to my requirements
A:Yes, you can tell us your requirements and ideas, we can design drawings, or provide samples, 2D floor plans or 3D drawings (support proe, solidwork, core, Auto CAD, DXF, DWG, step file formats).
Q: Are you trading company or manufacturer ?
A: We are factory.
Q:When our company be established?
A: We started from year 2013
Q: Can you provide samples for customers?
A: Yes, but the shipping will be charged on the customer's account.
Q:Do you offer OEM services?
A: We accept OEM, ODM. Cable sizes and materials can be customized.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.