10 Points 19 Inch Touch Panel Assembly Tape Bonding With LCM
Master Touch 19 Inch 10 Touch Points Touch panel Tape Bonding with LCM
1. Product Description
Master Touch 19 inch Touch Panel+LCM (Tape Bonding) is the lamination of touch panel and the LCD module. That is, simply use glue to laminate the touch screen and the four sides of the LCD screen, so there will be an air layer between them. The TP assembly attached by the frame bonding technology is thick, and the dust and water vapor are easy to enter the gap between the touch panel and the display. In addition, this type of lamination will make light reflection on screen obvious, so the display effect is much worse than that of optical bonding. But the advantage is that the lamination is simpler, the process is more mature, the yield is more stable, and the cost is lower.
2. Genaral Specification
2.1 LCD
| Model | DV190E0M-N11 |
| Size | 19 inch |
| Resolution | 1280(RGB)×1024 SXGA 86PPI |
| Luminance | 250 (Typ.) |
| Contrast | 1000 : 1 (Typ.) |
| Viewing Angles | 89/89/89/89 (Typ.)(CR≥10) |
| Signal System | 30 pins LVDS (2 ch, 8-bit) |
| Operating frequency | 60Hz |
| Driving Voltage | 5.0V (Typ.) |
|
TFT thickness |
9.9mm |
2.2 Touch Panel
| Outline Dimension | 415.8*340.45 | mm |
| View Area | 376.32*301.02(19 inch) | mm |
| TP thickness | 3.9 | mm |
| Total | 14.8 | mm |
| Touch IC | -- | |
| Number of touchpoint | 10 | points |
| Number of button | -- | - |
|
Interface information driven plate |
USB | - |
| The active information | -- | -- |
| The type of Bonding with LCD | Frame bonding | |
| Operation Temperature | -20℃~70℃ | ℃ |
|
Storage (cannot exceed 6 months) |
Temperature: 23±3℃ (Before installation) Humidity:40%~70%RH |
℃ |
| Temperature: -30~80℃ (After installation) | ℃ |
| Item |
Content |
| Transparency | 85±10% |
2.4 Electrical Spec.
| ESD Touch Side (Touch) | 4kv |
| ESD Touch Side (Air) | 8kv |
3. Reliability
| Item | Specifications | Remark |
|
High Temperature Operation |
70ºC, 48hrs | -- |
| Low Temperature Operation | -20 ºC, 48hrs | Non-condensing |
|
Operating Temperature/ Humidity |
60ºC/90%RH, 500hrs | Non-condensing |
| Thermal Shock |
-30 ~ 80℃, 60 mins/cycle, total 48 cycles |
-- |
4. Drawing
5. Details
6. Notice
Due to the system of capacitive touch screen is made of glass, Please do not strong impact, The impact,Or Fall from height;
Please do not stack up TPs. Don’t load on TP;
Please do not put the capacitive touch screen itself or FPC direct contact with metal material;
When assembling, please do not bend or strength to pull FPC, Avoid to cause the injured;
When assembling, please do not touch ink face of back of TP, Avoid to scratches;
When assembling, please do not contact the visual area, if have dirty in VA, Recommend the use of anhydrous ethanol to clean;
Operation of the capacitive touch screen, Use finger or conductive touch pen, please; must avoid high voltage and static electricity.
7. FAQ
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.