30 Pin Edp TFT HD Display Anti Glare 11.6 Inch LCD 1920x1080 All Viewing Angle 220 Nit
11.6 Inch 1920x1080 Tft Lcd All Viewing Angle 30 Pin Edp 220 Nit
General Description:
The manufacturer of M116B30-040-121-0102 is BOE. The display mode is Normally black. The contrast ratio is 1000:1, the color saturation is 72%NTSC, the response time is 25 ms, the optimal viewing Angle is symmetrical, the operating temperature is 0℃ to +50℃, and the storage temperature is -10℃ to +60℃.
Specifications:
| Parameter | Specification | Unit | Note |
| Display size | 11.6” (Diagonal) | inch | |
| Active area | 256.32(H) ×144 . 18(V) | mm | |
| Pixel Format | 1920(H) ×1080(V) (1pixel = R + G + B dot) | pixel | |
| Pixel pitch | 0.1335(H) x 0.1335 (V) | mm | |
| Pixel configuration | R, G, B vertical stripe | ||
| Display mode | Normally black | ||
|
Surface treatment of front polarizer |
Anti-glare coating: (3H) |
Interface Connection:
| Pin No. | Symbol | I/O | Function | Remark |
| 1 | CABC_EN / NC | - | Reserved for CD | [Note1] |
| 2 | H_GND | P | High Speed round | [Note2] |
| 3 | Lane1_N | I | Complement Signal Link Lane 1 | |
| 4 | Lane1_P | I | True Signal Link Lane 1 | |
| 5 | H_GND | P | High Speed round | [Note2] |
| 6 | Lane0_N | I | Complement Signal Link Lane 0 | |
| 7 | Lane0_P | I | True Signal Link Lane 0 | |
| 8 | H_GND | P | High Speed round | [Note2] |
| 9 | AUX_CH_P | I | True Signal Auxiliary Channel | |
| 10 | AUX_CH_N | I | Complement Signal Auxiliary Channel | |
| 11 | H_GND | P | High Speed round | [Note2] |
| 12 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
| 13 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
| 14 | NC | I | Reserved for LCD manufacturer’s use | [Note1] |
| 15 | LCD_GND | P | LCD logic and driver ground | |
| 16 | LCD_GND | P | LCD logic and driver ground | |
| 17 | HPD | O | HPD signal pin | |
| 18 | LED-1 | P | Backlight ground | |
| 19 | LED-2 | P | Backlight ground | |
| 20 | LED-3 | P | Backlight ground | |
| 21 | LED-4 | P | Backlight ground | |
| 22 | BL_ENABLE | I | Backlight on/off | |
| 23 | BL_PWM_DIM | I | System PWM | |
| 24 | SCL/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
| 25 | SDA/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
| 26 | BL_PWR | P | Backlight power | |
| 27 | BL_PWR | P | Backlight power | |
| 28 | BL_PWR | P | Backlight power | |
| 29 | BL_PWR | P | Backlight power | |
| 30 | NC | - | Reserved for LCD manufacturer’s use | [Note1] |
CN1 (eDP signals , +3.3V DC power supply and B/L power supply)
[Note1] Don’t input any signals or any powers into a NC pin. Keep the NC pin open.
[Note2] The shielding case is connected with signal GND.Connector used :20455-030E-76(I-PEX),Corresponding connector : 20453-030T (I-PEX)
Absolute Maximum Ratings:
| Parameter | Symbol | Condition | Ratings | Unit | Remark | |
| MIN | MAX | |||||
| +3.3V supply voltage | VDD | Ta=25℃ | -0.3 | +3.6 | V | |
| Backlight supply voltage | VBL | Ta=25℃ | -0.3 | +21 | V | |
| Input voltage(eDP) | VI | Ta=25℃ | -0.3 | +1.5 | V | |
| Input voltage(BL) | VBL_I | Ta=25℃ | -0.3 | VDD+0.3 | V | |
| Storage temperature | Tstg | -10 | +60 | ℃ |
|
|
| Operation temperature | Topa | 0 | +50 | ℃ | ||
“Absolute Maximum Ratings” is regulations that do not exceed it even momentarily.
Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
Backlight Driving:
The backlight system is an edge-lighting type with white-LED.
(It is usually required to measure under the following condition: Ta=25C±2C)
| Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
| Supply voltage | VBL | 7.0 | 12.0 | 21.0 | V | |
|
Current dissipation |
IBL |
- |
(227) | (251) | mA | VBL=12V Duty Ratio=100% |
| (135) | (135) | mA | VBL=7.9V Duty Ratio=40% | |||
| Modulated light signal voltage | VPWM H | 1.85 | - | VDD | V | |
| VPWM L | 0 | - | 0.7 | V | ||
| Brightness Control Duty Ratio | Duty | 1 | - | 100 | % | |
| Brightness Control pulse width | TPWM | 5 | - | - | ps | |
| Brightness Control frequency | PWM | 200 | - | 2,000 | Hz | |
| LED-BL ON/OFF High voltage | VCNT H | 1.8 | 3.3 | 3.6 | V |
Optical Specification:
| Paramete | Conditions | Min. | Typ. | Max. | Unit | |
|
Viewing Angle(CR>10) |
Horizontal | L | - | 89 | - |
degree |
| R | - | 89 | - | |||
| Vertical | T | - | 89 | - | ||
| B | - | 89 | - | |||
| Contrast Ratio | Center | 700 | 1000 | - | - | |
| Response Time | Tr+Td | - | 25 | ms | ||
|
CF Color Chromaticity(CIE1931) |
Red x |
Typ. -0.05 |
TBD |
Typ. +0.05 |
- | |
| Red y | TBD | - | ||||
| Green x | TBD | - | ||||
| Green y | TBD | - | ||||
| Blue x | TBD | - | ||||
| Blue y | TBD | - | ||||
| White x | (0.313) | - | ||||
| White y | (0.329) | - | ||||
| NTSC ratio | % | (72) | - | |||
| Luminance of white | YLI | 220 | cd/m | |||
Handling Precautions:
1.Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye or mouth by mistake.
2.If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan.
3.Do not expose the LCD module to a direct sunlight, for a long period of time to protect the module from the ultra violet ray.
Reliability Test Items:
| No. | Test Item | Conditions |
| 1 | High temperature storage test | Ta=60℃ 72h |
| 2 | Low temperature storage test | Ta=-10℃ 72h |
| 3 |
High temperature & high humidity operation test |
Ta=40℃90%RH 72h (No condensation) |
| 4 | High temperature operation test | Ta=50℃ 72h |
| 5 | Low temperature operation test | Ta=0℃ 72h |
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.