Full Viewing Angle 20 Pin 15 Inch LCD Display 1024x768 Lvds
15 Inch Tft Display 1024x768 Full Viewing Angle Lvds Interface 20 Pins
General Description:
DV150X0M-N10 manufacturer is BOE, type is a-Si TFT-LCD , LCD module, resolution 1024(H) × 768(V), pixel arrangement RGB vertical bar, display area 304.128(H) × 228.096(V) mm, external dimensions 326.5(H) × 253.5(V) × 9.7(D) mm.
Features:
- LVDS interface with 1 pixel / clock
- High-speed response
- Low color shift image quality
- 6-bit +FRC color depth, display 16.7M colors
- Wide viewing angle
- DE (Data Enable) only mode
- ADS technology is applied for high display quality
- RoHS compliant
Specifications:
| Parameter | Specification | Unit | Remarks |
| Active area | 304. 128(H) × 228.096(V) | mm | |
| Number of pixels | 1024(H) × 768(V) | pixels | |
| Pixel pitch | 0.297(H) × 0.297(V) | mm | |
| Pixel arrangement | Pixels RGB Vertical stripe | ||
| Display colors | 16.7M | colors | 6bits+FRC |
| Display mode | Normally Black | ||
| Dimensional outline | 326.5(H) × 253.5(V) × 9.7(Total) | mm | Detail refer to drawing |
| Weight | 930 | g | |
| Power Consumption | 8.72 | Watt | Typ. |
| Bezel width (L/R/U/D) | 10/10/11.7/11.7 | mm | |
| Surface Treatment | Haze 25%, 3H | ||
| Back-light | E-LED Light bar Type | ||
| LED life | 50000 | ||
| Display Direction | landscape & Portrait |
Absolute Maximum Ratings:
The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table.
| Parameter | Symbol | Min. | Max. | Unit | Remark |
| Power Supply Voltage | VDD | -0.3 | 4 | V | Ta = 25℃ |
| Operating Temperature |
TOP |
-20 | +70 | ℃ |
Note 1 |
|
Storage Temperature |
TSUR |
-20 | +70 | ℃ | |
|
TST |
-20 | +70 | ℃ | ||
| Operating Ambient Humidity | Hop | 10 | 90 | %RH | |
| Storage Humidity | Hst | 10 | 90 | %RH |
Note 1 : Wet bulb temperature should be 39℃ max. and no condensation of water.
Electrical Specifications:
| Parameter | Symbol | Values | Unit | Remark | |||
| Min | Typ | Max | |||||
| Power Supply Input Voltage | VDD | 3.0 | 3.3 | 3.6 | V | Note 1 | |
| Power Supply Current | IDD | - | 410 | 740 | mA | ||
| Power Supply Ripple Voltage | VRP | - | - | 300 | mV | ||
| Rush Current | IRUSH | - | 2 | 3 | A | Note 2 | |
|
LVDS Interface |
Differential Input High Threshold Voltage |
VLVTH |
- |
- |
+100 | mV |
VLVC=1.2V |
|
Differential Input Low Threshold Voltage |
VLVTL | - 100 |
- |
- |
mV | ||
| Common Input Voltage | VLVC | 0.7 | - | 1.6 | V | ||
|
CMOS Interface |
Input High Threshold Voltage |
VIH | 0.7VDD |
- |
VDD | V | |
|
Input Low Threshold Voltage |
VIL | 0 |
- |
0.3VDD | V | ||
|
Power Consumption |
PD | 0.8 | 1.3 | W | |||
| PBL | 7.92 | 8.71 | Note 3 | ||||
| Ptotal | 8.72 | 10.1 | |||||
Note 1 : The supply voltage is measured and specified at the interface connector of LCM.The current draw and power consumption specified is for VDD=3.3V,Test Pattern of power supply current.
Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min).
Note 3 :Calculated value for reference (Input pins*VPIN × IPIN) excluding inverter loss.
Backlight Electrical Specifications:
| Parameter | Min. | Typ. | Max. | Unit | Remarks | ||
| LED Driver Power Supply Voltage | HVDD | 10.8 | 12 | 12.6 | V | ||
| LED Driver Power Supply Current | IHVDD | 550 | 600 | 700 | mA | ||
|
EN Control Level |
Backlight on |
VENH |
3 | 3.3 | 3.6 | V |
EN logic high voltage |
| Backlight off |
VENL |
0 | 0 | 0.6 | V |
EN logic low voltage |
|
|
PWM Control Level |
PWM High Level |
VPML |
3 | 3.3 | 3.6 | V | |
| PWM Low Level |
VPML |
0 | 0 | 0.6 | V | ||
| PWM Control Frequency | F PWM | 0.12 |
- |
20 | KHz | Refer to customer comments | |
| Duty Ratio | - | 5 | - | 100 | % | ||
| LED Life-Time | N/A | 50,000 | - | - | Hour | ||
| LED Light Bar Input Voltage Per Input Pin | VPIN | 32.4 | 36 | 39.6 | V | ||
| LED Light Bar Input Current Per Input Pin | IPIN |
- |
55 |
- |
mA | ||
| LED Power Consumption | PBL | - | 7.92 | 8.71 | W | ||
Interface Connection:
| Pin No | Symbol | Description | Pin No | Symbol | Description |
| 1 | VDD | Power Supply, 3.3V(typ.) | 11 | RIN2- | -LVDS differential data input 2 |
| 2 | VDD | Power Supply,3.3V(typ.) | 12 | RIN2+ | +LVDS differential data input 2 |
| 3 | VSS | Ground | 13 | VSS | Ground |
| 4 | NC | No Connection | 14 | CLKIN- | -LVDS differential clock input CLK |
| 5 | RIN0- | -LVDS differential data input 0 | 15 | CLKIN+ | +LVDS differential clock input CLK |
| 6 | RIN0+ | +LVDS differential data input 0 | 16 | VSS | Ground |
| 7 | VSS | Ground | 17 | RIN3- | -LVDS differential data input 3 |
| 8 | RIN1- | -LVDS differential data input 1 | 18 | RIN3+ | +LVDS differential data input 3 |
| 9 | RIN1+ | +LVDS differential data input 1 | 19 | VSS | Ground |
| 10 | VSS | Ground | 20 | NC | No Connection |
Optical Specification:
| Parameter | Symbol | Condition | Min | Typ | Max | Unit | Remark | ||
|
Viewing Angle |
Horizontal | Θ3 |
CR > 10 |
85 | 89 | Deg. |
Note 1 |
||
| Θ9 | 85 | 89 | Deg. | ||||||
| Vertical | Θ12 | 85 | 89 | Deg. | |||||
| Θ6 | 85 | 89 | Deg. | ||||||
| Brightness | Lv |
Θ = 0. ILED=55m A |
315 | 350 | nit | ||||
| Uniformity | 9 Points | ΔY9 | 75% | 80% | |||||
| Contrast ratio | CR |
Θ = 0. |
700:1 | 1000:1 | - | ||||
|
Reproduction of color |
White |
Wx |
Θ = 0. (Center) Normal Viewing Angle |
TYP. - 0.03 |
0.313 |
TYP. + 0.03 |
|
||
| Wy | 0.329 | ||||||||
| Red | Rx | 0.649 | |||||||
| Ry | 0.338 | ||||||||
| Green | Gx | 0.323 | |||||||
| Gy | 0.627 | ||||||||
| Blue | Bx | 0.155 | |||||||
| By | 0.056 | ||||||||
| Color Gamut | 67 | 72 | - | % | |||||
| Response Time | Tr+Tf | - | 30 | 35 | ms | ||||
| Gamma Scale | 2.0 | 2.2 | 2.4 | ||||||
Note :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o‟clock direction and the vertical or 6, 12 o‟clock direction with respect to the optical axis which is normal to the LCD surface.
Operating Precautions:
1.Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
2.Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.