Bar Type 51 Pins LCD Display Module 1920x540 IPS Lvds Screen
29 Inch Bar Type Tft Lcd 1920x540 Ips Viewing Angle Lvds Interface 51 Pins
General Description:
The backlight of DV290FBM-N10 adopts WLED light-emitting side entry light source (bottom) with 50K hours of light source life without backlight driver. The LVDS (2 ch, 8-bit) signal interface is used, with a total of 51 pins, using terminal connections, and a drive screen voltage of 12.0V (Typ.). It has a typical vertical refresh rate of Fv of 60Hz.
Features:
1.LVDS interface with 2 pixel / clock
2.High-speed response
3.Low color shift image quality
4.8-bit color depth, display 16.7M colors
5.Wide viewing angle
6.DE (Data Enable) only mode
7.HADS technology is applied for high display quality
8.RoHS compliant
Specifications:
| Parameter | Specification | Unit | Remarks |
| Active area | 705.6(H)x198.45(V) | mm | |
| Number of pixels | 1920(H) × 540(V) | pixels | |
| Pixel pitch | 122.5(H) x367.5(V) | um | |
| Pixel arrangement | Pixels RGB Vertical stripe | ||
| Display colors | 16.7M | colors | 8bits True |
| Display mode | Normally Black | ||
| Dimensional outline | 720.8(H)*226.25(V)*8.4(Body) | mm | Total thickness 21mm |
| Weight | 2415± 100 | g | |
| Power Consumption | 40.66 | Watt | Typ. |
| Bezel width (L/R/U/D) | 5.6/5.6/11.9/11.9 | mm | |
| Surface Treatment | Haze 25% /3H | ||
| Back-light | E-LED , 2ea LED bar-down side | ||
| Possible display type | Landscape and Portrait Enabled |
Absolute Maximum Ratings:
| Parameter | Symbol | Min. | Max. | Unit | Remark |
| Power Supply Voltage | VDD | 8 | 13.2 | V | Ta = 25 ℃ |
| Operating Temperature | TOP | 0 | +50 | ℃ | |
|
Storage Temperature |
TSUR |
-20 | +60 | ℃ |
|
|
TST |
-20 | +60 | ℃ | ||
| Operating Ambient Humidity | Hop | 10 | 80 | %RH | |
| Storage Humidity | Hst | 10 | 80 | %RH |
Electrical Specifications:
| Parameter | Symbol | Values | Unit | |||
| Min | Typ | Max | ||||
| Power Supply Input Voltage | VDD | 10.8 | 12 | 13.2 | Vdc | |
| Power Supply Ripple Voltage | VRP | 400 | mV | |||
| Power Supply Current | IDD | - | 250 | 500 | mA | |
| Power Consumption | PDD | - | 3 | 6.6 | Watt | |
| Rush current | IRUSH | - | - | 3.0 | A | |
|
LVDS Interface |
Differential Input High Threshold Voltage |
VTH |
- |
+100 | mV | |
|
Differential Input Low Threshold Voltage |
VTL | -100 |
- |
mV | ||
| Common Input Voltage | VLC | 0.7 | - | 1.6 | V | |
| LVDS swing voltage | VID | ± 100 | ± 600 | mV | ||
|
CMOS Interface |
Input High Threshold Voltage |
VIH | 2.1 |
- |
3.6 | V |
|
Input Low Threshold Voltage |
VIL | 0 | 1.1 | V | ||
| Input current | IIN | -10 | - | 10 | µA | |
| Pull low resistor | RPD | 50 | 100 | 150 | KQ | |
Interface Connection:
|
Pin No |
Symbol | Description |
Pin No |
Symbol | Description |
| 1 | VDD | Power Supply (12V) | 27 | ELV1N | Negative Transmission data of Pixel 1 (EVEN) |
| 2 | VDD | Power Supply (12V) | 28 | ELV1P | Positive Transmission data of Pixel 1 (EVEN) |
| 3 | VDD | Power Supply (12V) | 29 | ELV2N | Negative Transmission data of Pixel 2 (EVEN) |
| 4 | VDD | Power Supply (12V) | 30 | ELV2P | Positive Transmission data of Pixel 2 (EVEN) |
| 5 | VDD | Power Supply (12V) | 31 | GND | Ground |
| 6 | NC | Not connection, this pin should be open | 32 | ELVCKN | Negative Transmission Clock(EVEN) |
| 7 | GND | Ground | 33 | ELVCKP | Positive Transmission Clock(EVEN) |
| 8 | GND | Ground | 34 | GND | Ground |
| 9 | GND | Ground | 35 | ELV3N | Negative Transmission data of Pixel 3 (EVEN) |
| 10 | OLV0N | Negative Transmission data of Pixel 0 (ODD) | 36 | ELV3P | Positive Transmission data of Pixel 3 (EVEN) |
| 11 | OLV0P | Positive Transmission data of Pixel 0 (ODD) | 37 | NC | Not connection, this pin should be open |
| 12 | OLV1N | Negative Transmission data of Pixel 1 (ODD) | 38 | NC | Not connection, this pin should be open |
| 13 | OLV1P | Positive Transmission data of Pixel 1 (ODD) | 39 | GND | Ground |
| 14 | OLV2N | Negative Transmission data of Pixel 2 (ODD) | 40 | NC | Not connection, this pin should be open |
| 15 | OLV2P | Positive Transmission data of Pixel 2 (ODD) | 41 | NC | Not connection, this pin should be open |
| 16 | GND | Ground | 42 | NC | Not connection, this pin should be open |
| 17 | OLVCKN | Negative Transmission Clock(ODD) | 43 | NC | Not connection, this pin should be open |
| 18 | OLVCKP | Positive Transmission Clock(ODD) | 44 | NC | Not connection, this pin should be open |
| 19 | GND | Ground | 45 | LVDS_SE L | LVDS format select |
| 20 | OLV3N | Negative Transmission data of Pixel 3 (ODD) | 46 | NC | Not connection, this pin should be open |
| 21 | OLV3P | Positive Transmission data of Pixel 3 (ODD) | 47 | NC | Not connection, this pin should be open |
| 22 | NC | Not connection, this pin should be open | 48 | NC | Not connection, this pin should be open |
| 23 | NC | Not connection, this pin should be open | 49 | SCL_PG | I2C_SCL used for BOE |
| 24 | GND | Ground | 50 | SDA_PG | I2C_SDA used for BOE |
| 25 | ELV0N | Negative Transmission data of Pixel 0 (EVEN) | 51 | NC | Not connection, this pin should be open |
| 26 | ELV0P | Positive Transmission data of Pixel 0 (EVEN) |
Optical Specification:
| Parameter | Symbol | Condition | Min | Typ | Max | Unit | ||
|
Viewing Angle |
Horizontal |
Θ3 |
CR > 10 |
80 | 89 | - | Deg. | |
| Θ9 | 80 | 89 | - | Deg. | ||||
|
Vertical |
Θ12 | 80 | 89 | - | Deg. | |||
| Θ6 | 80 | 89 | - | Deg. | ||||
| Brightness | Lv |
Θ=0° (Center) Normal Viewing Angle |
560 | 700 | - | nit | ||
| Contrast ratio | CR | 800:1 | 1200:1 | - | ||||
| White Luminance uniformity | ΔY | 75 |
- |
- |
% | |||
|
Reproduction of color |
White |
Wx |
TYP. - 0.03 |
0.271 |
TYP. + 0.03 |
|||
|
Wy |
0.292 | |||||||
|
Red |
Rx |
0.650 | ||||||
|
Ry |
0.332 | |||||||
|
Green |
Gx |
0.287 | ||||||
|
Gy |
0.616 | |||||||
|
Blue |
Bx |
0.145 | ||||||
|
By |
0.082 | |||||||
| Color Gamut | 69 | 72 | - | % | ||||
| Response Time | G to G | Tg | - | 15 | - | ms | ||
Handling Precautions:
1.Design the length of cable to connect between the connector for back-light and the converter as shorter as possible and the shorter cable shall be connected directly , The long cable between back-light and Converter may cause the Luminance of LED to lower and need a higher startup voltage.
2.Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.