Super Voltage Converter

The ICL7660S Super Voltage Converter is a monolithic CMOS voltage conversion IC that guarantees significant performance advantages over other similar devices. It is a direct replacement for the industry standard ICL7660 offering an extended operating supply voltage range up to 12V, with lower supply current. No external diode is needed for the ICL7660S. In addition, a Frequency Boost pin has been incorporated to enable the user to achieve lower output impedance despite using smaller capacitors. All improvements are highlighted in the Electrical Specifications section. Critical parameters are guaranteed over the entire commercial, industrial and military temperature ranges.

The ICL7660S performs supply voltage conversion from positive to negative for an input range of 1.5V to 12V, resulting in complementary output voltages of -1.5V to -12V. Only 2 non-critical external capacitors are needed for the charge pump and charge reservoir functions. The ICL7660S can be connected to function as a voltage doubler and will generate up to 22.8V with a 12V input. It can also be used as a voltage multiplier or voltage divider.

The chip contains a series DC power supply regulator, RC oscillator, voltage level translator, and four output power MOS switches. The oscillator, when unloaded, oscillates at a nominal frequency of 10kHz for an input supply voltage of 5.0V. This frequency can be lowered by the addition of an external capacitor to the “OSC” terminal, or the oscillator may be over-driven by an external clock.

The “LV” terminal may be tied to GND to bypass the internal series regulator and improve low voltage (LV) operation. At medium to high voltages (3.5V to 12V), the LV pin is left floating to prevent device latchup.

Features

• Guaranteed Lower Max Supply Current for All Temperature Ranges

• Wide Operating Voltage Range 1.5V to 12V

• 100% Tested at 3V

• No External Diode Over Full Temperature and Voltage Range

• Boost Pin (Pin 1) for Higher Switching Frequency

• Guaranteed Minimum Power Efficiency of 96%

• Improved Minimum Open Circuit Voltage Conversion Efficiency of 99%

• Improved SCR Latchup Protection

• Simple Conversion of +5V Logic Supply to ±5V Supplies

• Simple Voltage Multiplication VOUT = (-)nVIN

• Easy to Use - Requires Only 2 External Non-Critical Passive Components

• Improved Direct Replacement for Industry Standard ICL7660 and Other Second Source Devices

• Pb-Free Plus Anneal Available (RoHS Compliant)

Applications

• Simple Conversion of +5V to ±5V Supplies

• Voltage Multiplication V_OUT = ±nV_IN

• Negative Supplies for Data Acquisition Systems and Instrumentation

• RS232 Power Supplies

• Supply Splitter, V_OUT = ±V_S/2

Absolute Maximum Ratings

Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13.0V

LV and OSC Input Voltage (Note 3)

    V+ < 5.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V+ + 0.3V

    V+ > 5.5V . . . . . . . . . . . . . . . . . . . . . . . . . . .V+ -5.5V to V+ +0.3V

Current into LV (Note 3)

    V+ > 3.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20µA

Output Short Duration

    V_SUPPLY ≤ 5.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Continuous

Storage Temperature Range . . . . . . . . . . . . . . . . . . .-65°C to 150°C

Operating Conditions

Temperature Range

    ICL7660SI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C

    ICL7660SC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C

Thermal Information

Thermal Resistance (Typical, Note 4)          θ_JA (°C/W)      θ_JC (°C/W)

    PDIP* . . . . . . . . . . . . . . . . . . . . . . . . . .       110                N/A

    Plastic SOIC. . . . . . . . . . . . . . . . . . . . .        160                N/A

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C

    (SOIC - Lead Tips Only)

*Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing. applications.

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

3. Connecting any terminal to voltages greater than V+ or less than GND may cause destructive latchup. It is recommended that no inputs from sources operating from external supplies be applied prior to “power up” of ICL7660S.

4. θ_JA is measured with the component mounted on an evaluation PC board in free air.

Pinout

ICL7660S (PDIP, SOIC) TOP VIEW

Stock Offer (Hot Sell)