Pre-Owned Rohde and Schwarz FSU67 Spectrum Analyzer with 20Hz to 67GHz Range and Low Noise Floor

The R&S FSU67 is the first spectrum analyzer with a direct frequency range to 67 GHz and fundamental mixing. It allows measurements to 67 GHz without using cumbersome setups with external mixers.

• Simplified test set-ups with just one connection from 20 Hz to 67 GHz
• Full span sweep of 67 GHz
• Unambiguous frequency indication without the image response and multiple responses known from external harmonic mixers
• Wider level range with a much higher allowable reference level than with harmonic mixers
• Good level accuracy to 67 GHz
• Low noise floor: -152 dBm (1 Hz) at 2 GHz, -130 dBm (1 Hz) at 65 GHz
• Wide range of resolution bandwidth: 1 Hz to 50 MHz
• Versatile filter characteristics: Gaussian, channel filters, FFT, 6-dB EMI filters
• Full range of detectors including RMS, quasipeak
• Comprehensive power measurement functions (CP, ACP, time domain power)
• NRP power heads can be connected directly (Option FS-K9 and NRP-Z6 required)
• Harmonic distortion and spurious emissions measurement function
• High display linearity < 0.1 dB
• Phase noise and noise figure application firmware
• External generator control for use of an external microwave generator as tracking generator for scalar network measurements

• R&S® FSU3: DC coupled 20 Hz to 3.6 GHz AC coupled 1 MHz to 3.6 GHz
• R&S® FSU8: DC coupled 20 Hz to 8 GHz AC coupled 1 MHz to 8 GHz
• R&S® FSU26: DC coupled 20 Hz to 26.5 GHz AC coupled 10 MHz to 26.5 GHz
• R&S® FSU43: DC coupled 20 Hz to 43 GHz
• R&S® FSU46: DC coupled 20 Hz to 46 GHz
• R&S® FSU50: DC coupled 20 Hz to 50 GHz Frequency range
• R&S® FSU67: DC coupled 20 Hz to 67 GHz Frequency resolution 0.01 Hz

The Rohde & Schwarz R&S FSU67 Spectrum Analyzer surpasses the proven excellent RF data of the R&S FSE and R&S FSIQ series of Spectrum Analyzers. Measurements calling for an extremely wide dynamic range are simpler, faster and more reliable - in development, quality management and production environments.

The R&S FSU67 can rightly be called the new reference in spectrum analysis, with an unprecedented dynamic range:

• TOI >20 dBm, typ. +25 dBm
• 1 dB compression (0 dB RF attenuation): +13 dBm
• Displayed average noise level: -158 dBm (1 Hz bandwidth)
• 77 dB ACLR typ. for 3GPP, 84 dB typ. with noise correction
• HSOI 55 dBm typ.
• Phase noise: -160 dBc/Hz typ. at 10 MHz carrier offset

The R&S FSU series of spectrum analyzers launched with the most abundant functionality available on the spectrum analyzer market. All major functions come straight away in the basic unit and include:

• Highly selective digital filters from 10 Hz to 100 kHz
• Fast FFT filters from 1 Hz to 30 kHz
• Channel filters from 100 Hz to 5 MHz
• RRC filters
• 1 Hz to 50 MHz resolution bandwidth
• QP detector and EMI bandwidths 200 Hz, 9 kHz, 120 kHz
• 2.5 ms sweep time in frequency domain
• 1 µs sweep time in time domain
• Number of measurement points/trace selectable between 155 and 10001
• Time-selective spectrum analysis with gating function
• GPIB interface, IEEE 488.2
• RS-232-C serial interface, 9-pin SUB-D connector
• VGA output, 15-pin SUB-D
• PC-compatible screenshots on diskette or hard disk
• Up to 20 measurements/s in manual mode
• Up to 30 measurements/s on GPIB interface
• SCPI-compatible GPIB command set
• R&S FSE R&S FSIQ compatible GPIB command set
• Fast ACP measurement in time domain
• Statistical signal analysis with CCDF function
• RMS detector of 100 dB dynamic range
• Transducer factor for correcting antenna or cable frequency responses
• 2-year calibration cycle
• External reference from 1 MHz to 20 MHz in 1 Hz steps
• GGSM/EDGE modulation measurements (with option R&S FS-K5)