800W / 1000W Powered Audio Amplifier speaker 2u Power Amplifier
Price:
$170.00 - $1,340.00/pieces
MOQ:
2 pieces
Delivery Time:
Negotiable
Brand:
VA
Product Description
Product Description
High Quality Powered 2*800W 2*1000W 2*1300W 2*1600W 2U Audio Amplifier
1. Mains Power Switch
When press the switch, the soft start circuit run for avoiding surge strike. In about 3-4 seconds, there will be a clicking
denote that soft start finished. And more 1-2 seconds later, there will be another “clicking”, the amplifier is connected with
speaker and ready to work.
2. CH-1/CH-2 Input level control
Adjust it to get the volume desired. Use CH-1 control only while amplifier is set in Bridge or Parallel mode.
3. CH-1/CH-2 Protection indicating LED
This red LED will light up when the amplifier is running un-stable or went in to thermal protection after the power elements
temperature over 90℃.
4. Clip LED
Turns on just before the maximum, distortion free, output level of the amplifier. The clip Leds may turn on shortly from time to time but they may certainly not turn on for longer periods. In this case you have to turn the output level down!— 3 —
5. Signal LED
The green signal led indicates that a music signal is present at this channel input.
6. Parallel mode indicating LED
Indicate that the amplifier is working under parallel mode, the indicator is lighten, input signal only acts on CH-1.
7. Bridge mode indicating LED
Indicate the amplifier is working under BRIDGE mode, the indicator is lighten , and the input signal only acts on CH-1
When press the switch, the soft start circuit run for avoiding surge strike. In about 3-4 seconds, there will be a clicking
denote that soft start finished. And more 1-2 seconds later, there will be another “clicking”, the amplifier is connected with
speaker and ready to work.
2. CH-1/CH-2 Input level control
Adjust it to get the volume desired. Use CH-1 control only while amplifier is set in Bridge or Parallel mode.
3. CH-1/CH-2 Protection indicating LED
This red LED will light up when the amplifier is running un-stable or went in to thermal protection after the power elements
temperature over 90℃.
4. Clip LED
Turns on just before the maximum, distortion free, output level of the amplifier. The clip Leds may turn on shortly from time to time but they may certainly not turn on for longer periods. In this case you have to turn the output level down!— 3 —
5. Signal LED
The green signal led indicates that a music signal is present at this channel input.
6. Parallel mode indicating LED
Indicate that the amplifier is working under parallel mode, the indicator is lighten, input signal only acts on CH-1.
7. Bridge mode indicating LED
Indicate the amplifier is working under BRIDGE mode, the indicator is lighten , and the input signal only acts on CH-1
1. CH-1/CH-2 input XLR
standard XLR jack, below is the connection method;
Pin1: signal ground, Pin2: signal+, Pin3: signal-
2. CH-1/CH-2 Signal Link Output
Standard XLR (male) socket for input signal link, its Pins parallel connected with the female XLR socket so you can feed the same signal to another amplifier. Pin1: signal ground, Pin2: signal+, Pin3: signal-
standard XLR jack, below is the connection method;
Pin1: signal ground, Pin2: signal+, Pin3: signal-
2. CH-1/CH-2 Signal Link Output
Standard XLR (male) socket for input signal link, its Pins parallel connected with the female XLR socket so you can feed the same signal to another amplifier. Pin1: signal ground, Pin2: signal+, Pin3: signal-
3.INPUT SENSITIVITY SWITCH.
With this switch you can perfectly adapt the input sensitivity of the amplifier:26dB;1.4V;0.77V
4. CH-1/CH-2 35Hz HPF.
The low cut filter cuts all undesired frequencies below 35Hz.protecting woofers against excesslve swings.
5. Output Mode Set Switch.
Select the run mode as STEREO or BRIDGE or PARALLEL
6. Resettable fuse
When the amplifier malfunctions, the fuse will automatically disconnect the circuit loop; after the trouble is removed, the fuse will automatically reset, and resume working.
7. CH-1/CH-2 output SPEAKON
Standard Speakon socket. 1+ 2+ :, 1- 2-: -
8. Binding post outputs
These posts will accept bare wire cables that connect to your speakers.
9. Mains Power Supply Cord
With this switch you can perfectly adapt the input sensitivity of the amplifier:26dB;1.4V;0.77V
4. CH-1/CH-2 35Hz HPF.
The low cut filter cuts all undesired frequencies below 35Hz.protecting woofers against excesslve swings.
5. Output Mode Set Switch.
Select the run mode as STEREO or BRIDGE or PARALLEL
6. Resettable fuse
When the amplifier malfunctions, the fuse will automatically disconnect the circuit loop; after the trouble is removed, the fuse will automatically reset, and resume working.
7. CH-1/CH-2 output SPEAKON
Standard Speakon socket. 1+ 2+ :, 1- 2-: -
8. Binding post outputs
These posts will accept bare wire cables that connect to your speakers.
9. Mains Power Supply Cord
Specification
|
|
GW800
|
GW1000
|
|
|
Power handling
|
800W*2(8Ω)/1200W*2(4Ω)/2400W (8Ω)
|
1000W*2(8Ω)/1500W*2(4Ω)/3000W (8Ω)
|
|
|
Output Connections
|
Speakon & Binding Post
|
|
|
|
Frequency Response
|
20Hz-20KHz ±0.5dB
|
XLR-f
|
|
|
Input Sensitivity
|
0.775V/1.4V/26dB
|
XLR-m
|
|
|
Input Impedance
|
20kΩ/Balanced,10kΩ/un-Balanced
|
20kΩ/Balanced,10kΩ/un-Balanced
|
|
|
S/N Ratio
|
≥100dB
|
＜ 1%
|
|
|
THD
|
≤0.03%
|
20Hz-25kHz, ±1dB
|
|
|
Crosstalk @ Rated
Output/8Ω/1kHz |
＞70 dB
|
AC: 220-230V 50Hz
|
|
|
Damping
Factor/8Ω/1kHz |
＞240
|
12.4
|
|
|
Slew Rate
|
15V/uS
|
482*326*88mm
|
|
|
Protection
|
Soft Start,Short Circuit,Limiter,DC Fault,AC Line Fuse,Thermal Cut
|
|
|
|
Cooling system
|
Two steps speed fan
|
|
|
|
Mains Power supply
|
AC:220~230V 50Hz
|
|
|
|
Weight
|
23.5KG
|
25.2KG
|
|
|
Dimensions (WxDxH)
|
482x464.5×88 mm
|
|
|
|
|
GW1300
|
|
GW1600
|
|
|||
|
Power handling
|
1300W*2(8Ω)/2000W*2(4Ω)/4000W (8Ω)
|
|
1600W*2(8Ω)/2400W*2(4Ω)/4800W (8Ω)
|
|
|||
|
Output Connections
|
Speakon & Binding Post
|
|
|
|
|||
|
Frequency Response
|
20Hz-20KHz ±0.5dB
|
|
|
|
|||
|
Input Sensitivity
|
0.775V/1.4V/26dB
|
|
|
|
|||
|
Input Impedance
|
20kΩ/Balanced,10kΩ/un-Balanced
|
|
|
|
|||
|
S/N Ratio
|
≥100dB
|
|
|
|
|||
|
THD
|
≤0.05%
|
|
|
|
|||
|
Crosstalk @ Rated
Output/8Ω/1kHz |
＞70 dB
|
|
|
|
|||
|
Damping
Factor/8Ω/1kHz |
＞240
|
|
|
|
|||
|
Slew Rate
|
15V/uS
|
|
|
|
|||
|
Protection
|
Soft Start,Short Circuit,Limiter,DC Fault,AC Line Fuse,Thermal Cut
|
|
|
|
|||
|
Cooling system
|
Two steps speed fan
|
|
|
|
|||
|
Mains Power supply
|
AC:220~230V 50Hz
|
|
|
|
|||
|
Weight
|
26.5KG
|
|
27.5KG
|
|
|||
|
Dimensions (WxDxH)
|
482x464.5×88 mm
|
|
|
|
|||
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Guangzhou Concord Sound Industrial Co., Ltd.
Location
No. 36 Daping Industrial, Shatou street, Shiqiao, Panyu District, Guangzhou City, Guangzhou, Guangdong, China
Contact Person
Cassie