King Pin Kit KP-226 45# Steel 38.1x220mm HRC 55-62 Steering Knuckle Repair Kit for Isuzu Trucks

Complete king pin repair kit for Isuzu medium/heavy trucks (JCR, JBR, FTR, FSR, etc.). Includes king pin, bushings, bearings, seals, and hardware. Restores precise steering control and eliminates wheel play.

• Complete Kit: Contains all required components for a full king pin rebuild
• OE Quality: Manufactured to Isuzu dimensional and metallurgical specifiions
• Hardened King Pin: Induction-hardened and precision-ground for exceptional wear resistance
• Premium Bushings: High-lead bronze or steel-backed bushings with spiral grease grooves
• Thrust Bearing Included: Reduces friction between axle beam and steering knuckle
• Eliminates Steering Play: Restores proper clearances, removing vertical end play
• Reduces Tire Wear: Prevents uneven tire wear caused by loose king pins
• Extended Service Life: Can last hundreds of thousands of miles with proper lubriion
• Safety Critical: Ensures predictable steering and safe vehicle control
• Certified Quality: ISO9001, TS16949 certified
• 12-Month Warranty: Guaranteed quality and reliability

This king pin kit is specifically designed for Isuzu trucks with conventional solid front axle (I-beam).

• JCR (1978-1984)
• JBR (light/medium trucks)
• FCR (light/medium trucks)
• FDR (light/medium trucks)
• FTR (FTR33 10/1995-04/2000, FTR11 1984-1986, FTR12 1984-1992)
• FSR (FSR32, FSR33, FSR34)
• FRR (FRR34 FRD/FRR 10/2007-2015, FRR90)
• TXD, BC, TW, TS

Not engine-specific - fits various Isuzu diesel engines (4HK1, 6HK1, 6HH1, 4JB1, 4BG1, etc.)

1. Safely lift and support vehicle - remove front wheels and brake components
2. Remove steering knuckle - disconnect tie rod, drag link, and steering arm
3. Press out old king pins - use a hydraulic press. Remove old bushings
4. Inspect axle beam bores - check for ovality or damage. Clean thoroughly
5. Install new bushings - press into axle beam. Ensure oil holes align
6. Ream bushings to size (if required) - using precision reamer for correct clearance
7. Lubrie king pin - apply high-quality chassis grease
8. Assemble thrust bearing - place as per OE orientation. Install spacer if required
9. Insert king pin - tap into place using brass drift. Install lock pins
10. Check end play - use dial indior. Should be ≤ 0.005 inches
11. Reassemble steering knuckle, seals, caps - use Three Bond 1215 on sealing plug
12. Grease thoroughly - pump grease until fresh grease appears from all seals
13. Reinstall wheels and brake components - torque lug nuts and fasteners
14. Road test - check for smooth steering, no binding, no play. Re-torque after 500 km

• Material Verifiion: 45# Steel composition and hardness tested to OE specifiions
• Dimensional Accuracy: Pin diameter (38.1mm), length (220mm) verified with precision gauges
• Bushing Fitment Test: Sample bushings pressed and reamed to confirm proper clearance
• Hardness Testing: Rockwell hardness test on king pin and thrust bearing surfaces
• Surface Finish Inspection: Ground surfaces checked for smoothness (Ra ≤ 0.4 μm)
• Seal Quality Check: Dust seals and gaskets inspected for tears and correct fit
• Kit Completeness: Each kit 100% manually counted against component list
• Packaged Safely: Components individually wrapped to prevent transit damage

• Neutral export packing or customized packaging available
• Carton or wooden case for safe transportation
• Fast delivery for stock items
• Shipping by Express Air or Sea