The machine will have two tanks for keeping Liquid A & B separately.
There are two sets of metering pumps inside the machine, draining out liquids individually from tank A & B. Liquid A & B mix with each other in the mixer pipe and dispensed out according to the programmable data .
Automatic glue mixing machine is mainly used for a two-component glue( Epoxy/ Silicone/PU,etc adhesive), automatic metering and mixing the ratio by two sets of high precision pumps, supply to a fully mixing design and then dispensing , dosing , dispensing the aimed products .

* Machine picture :


* Working principle :


* Applications : 
photo frame , arts , crafts , Reverse Sensor, Electronic Circuit Board, Electronic Ballast ,air Filters, LED products ,Electronic components,Crafts,Ads modules, Capacitors, Power supply, Transformer, end cap for filter, solar junction box ,Power module, Ignition coil, Sensor, Photovoltaic module, Photovoltaic inverter. Etc

Epoxies , Urethane(PU) or Silicone .
Two components glue, AB glue, AB part glue, silicone, epoxy resin, polyurethane;
All kinds of two-component mixed glues with required ratio, such as epoxy resin AB glue, polyurethane, silica gel, PU glue,flocking glue, paint, etc.

* Company profile :

* Global activities

*Packing and delivery 

Common troubles and solutions

• 1.Glue dispenser always drops

  Drops always happened when valve closed . The reason may be low concentration of glue , big air-pressure or large diameter of needles.

  Narrow needles will effect the flow of the liquid and cause back pressure . It will lead to dropping when the valve closed . Too narrow needles will effect the drainage of air when valve start to work, but it can be solved if change suitable needles .

  Conical needles with less back pressure and liquid flow smoothly .

  It is better to drainage of the air advance or use no-foam glue or deaeration to avoid the air cause dropping after valve closed .

• 2.Glue dispensing not evenly

  The problem cause mainly because of the storage flow pressure tank or air pressure is not stable.

  Inlet pressure regulating table should be set lower 10-15psi than factory minimum pressure . The pressure in pressure tank should be set upper than the middle pressure of regulating table . It should be avoided to use the pressure lower than the middle pressure of regulating table .

  Control pressure of rubber valve at least higher than 60psi to assured glue evenly .

  We should check the glue output speed at last . The glue is uneven if the time less than 15/1000s , the output speed more longer , the glue dispensing will be more stable .

• 3.Slow flow velocity

  It should be changed the pipe from 1/4 to 3/8 if the flow velocity too slowly .

  The pipe is the shorter the better if no requirement .

• 4.Air in the fluid

  Excessive fluid pressure and short valve opening time may lead to the air infiltration liquid . We can use the conical needles and reduce fluid pressure .

• 5. Instant glue (quick adhesive) blocking in valve connector and pipes.

  This problem is caused by heavy moisture and recycle instant glue . We should make sure to use new instant glue and wash the pipes with dry . Make sure air dry and add filter between plant air pressure and valve .

• 6.UV glue (UV curing glue )

  Make sure to use black pipeline.

  Don't add new UV glue to old UV glue in pressure tank , we should drain off the old UV glue before pouring new UV glue into pressure tank because the UV glue will produce bubble after a period of time and lead to glue dispensing unevenly .

• 7.Needles

  Normally , it may cause air problem if the needle less than NO.20 . It is better to use large steel needles or conical needles to avoid to use winding needles.

• 8. Epoxy cleaning

  It is better to use storage pressure cylinder of methybenzene toluene to self-cleaning one time for each shift . The more frequently cleaning the better .