Cost-Effective Low-Voltage DC Barrier Gates: Efficient Access Control Easy Installation & Maintenance

• Remote control: switch control through remote control, convenient for remote operation.

• Auto-sensing: Automatically open the gate after detecting the vehicle through sensors (such as infrared, ground sensors, etc.).

• License plate recognition: Automatically open the gate by recognizing the license plate information of vehicles.

• Note: it is best to use BVR wire, do not use network wire

• The movement adopts side mounting type, easy installation and compact structure.
• The main body of the movement is made of aluminum alloy, manufactured by die-casting process, with reliable mechanical strength, beautiful appearance, precise size and good heat dissipation.

• The movement adopts gear reduction transmission, high transmission efficiency, small loss of power output; gear material SCM421, carburizing heat treatment process, precision grinding processing, anti-wear, impact resistance, service life far exceeds the worm gear transmission structure.

• The movement adopts DC brushless motor, with large output torque and small size, and the speed can be adjusted arbitrarily through the controller, and the deceleration buffer can be realized when dropping and lifting the pole into place, so that the gate pole can be put into place smoothly.

• The motor adopts DC24V safety voltage, which avoids the electric shock accident caused by leakage, and provides more protection for personal safety.

Internal Dimensions

Movement Outline Picture

Motor Lead Wire Definition

Working Environment

• Temperature range: -30°C ~ +60°C

• Humidity: 90% or less (No condensation)

• Altitude: Below 1000M

Storage Environment

Operating Life

Gate Pole Mounting Plate-Octagonal Pole

Barrier Commissioning Steps

Step 1: Match The Rod And Spring

Step 2: Limit Of Self Inspection Learning Switch Of Track Gate

• The normal startup of the controller is "00:00" and "e-00" alternately displayed. Press and hold the controller "close / turn up" for 2 seconds, and the track gate operates in the direction of closing. The controller scrolls from left to right to display "0 0 0 0", and the buzzer sounds rhythmically. When the motor runs to the closing limit, the controller displays static "0 0 0 0" and the buzzer stops ringing. At this time, the closing self-test is completed.
• After the closing self-test is completed, press and hold the controller "open / down" for 2 seconds, and the track gate operates in the opening direction. The controller scrolls from left to right to display "0 0 0 0", and the buzzer sounds rhythmically. When the motor runs to the opening limit, the controller buzzer sounds for a long time. At this time, the opening self-test is completed, and the gate can operate normally.

• The pole exceeds 90 degrees after driving to the position (adjust the P-9 parameter to a large scale); The pole is less than 90 degrees(reduce the P-9 parameter).
• Close to the position where the pole is higher than the horizontal position (reduce the P-6 parameter); The pole is below the level position (increase P-6).

Key Operation

Shortcut Key Operation

• Press the "on / down" button once in the mode without inserting the motor cable to display the software version number; Press the "off / up" key once to display the software date.
• In the normal working mode, under the display time page of the digital tube, short press "set / save" once to display the current value, short press "set / save" for the second time to display the change rate of hall, and short press "set / save" for the third time to display the internal voltage value of the controller; Short press "set / save" for the fourth time to display the power supply voltage value;

Key Function Description

• Set / save key: enter the setting state and save the setting value.

• On / down key: press this key to open the gate in normal working state. After entering the setting state, you can use this key to add menu items or adjust the setting value upward. In the parameter setting state, short press to add one each time. Press and hold continuously until the maximum value is reached, and then add from the minimum value.

• Off / up key: press this key to close the gate in normal working state. After entering the setting state, you can use this key to reduce menu items or adjust the setting value downward. In the parameter setting state, short press to subtract one at a time. Long press to continuously decrease to the minimum value and then decrease from the maximum value.

• Return / stop key: in normal working state, press this key to stop the brake. In the setting state, you can exit the setting state or return to the previous menu.

Parameter Menu

Operating Instructions

Parameter Command Value Table

• For all places involving angles, the closing position is 0 degrees.
• When the power supply voltage is too large (> 27V) or too small (< 18V), the controller will automatically protect and give an alarm.when the controller is protected, the motor, light box, ground sensor and other equipment will not work.

Remote Control Function

• Remote control pairing: long press the controller "set / save" for three seconds, find the P-F item, and press the "set / save" again to display "000". At this time, press any key of the remote control. At this time, after the controller makes a long sound, the display changes to P-F, indicating that the remote control is matched successfully.
• Clear the remote controller: long press "set / save" on the main board for three seconds, find the P-F item, press "set / save" again to display "000", adjust the value to 253, and press "set / save" again. At this time, after the main board makes a long sound, the display changes to P-F, and all remote controllers will be cleared.
• Fleet mode: long press "set / save" on the controller for three seconds, find item p-8, and then press "set / save" to display "0", adjust the value to 4, and then press "set / save" to exit the menu; After the road gate is opened in place, press the stop button of the remote controller for more than 2 seconds, and the fleet mode will start; To turn off the fleet mode, just press the off key of the remote controller.

Parameter Transfer Steps

• Step 1: debug a template

• Step 2: connect the template with the new controller

• Step 3: power on the new controller

• Step 4: long press the " down" button of the template, and check the "s -- s" displayed on the new controller, then the parameter transfer is successful

Common Problems And Solutions

• The self-inspection is not successful, and the gate is not running normally

• The vertical or horizontal position of the gate rod is not in place

• How to correctly judge whether the gate is really in place

Set the P-18 parameter of the controller to 1. If the relay is opened or closed once, it indicates that it has been opened / closed in place

Pay attention to observe whether the motor stops when the gate lever is in place, which means it is in place. If the gate lever is in place and the motor is still running, it is necessary to change the P-6 or P-9 parameters.

In the process of switching on and off, the nixie tube will have a dynamic "1" display. If the nixie tube display returns to the time interface, it indicates that it has been in place.

• Failure of rebound function in case of resistance

• The gate suddenly runs in the opposite direction during normal operation

• The gate was opened again when the gate was almost in place

Error codes and Solutions

BR-110	BR-110F	BR-110BY	BR-110L	BR-110H
Straight arm version Lifting time: 3s 6s	High speed version Lifting time 1.5s	LED ligtht version Lifting time: 3s 6s	90° Folding arm version Lifting time: 3s 6s	180° Folding arm version Lifting time: 3s 6s
BR-121	BRDC-110	BDC-1	BRC-433R	BRC-443T
Fence arm version Lifting time: 6s	DC power economy version Lifting time: 1.2-5s