A transparent inorganic coating for vehicle glass, combining hydrophilic wetting with antistatic performance to help reduce dust and stain adhesion.
GETSUN GT-1238 is a 1L nano glass coating for automotive windshields, side windows, rear windows and mirrors. Its nano-silica system contains approximately 5 nm titanium dioxide particles and forms a surface microstructure below 50 nm. After curing, the product creates an ultra-thin transparent layer while maintaining glass transparency.
Buyer need
Glass care involves more than removing existing dirt. For workshops and distributors seeking a surface treatment that helps reduce subsequent dust and stain adhesion, coating selection should consider surface preparation and the intended wetting behavior.
Product response
This hydrophilic glass coating has a stated contact angle below 10 degrees. Water spreads across the surface as a thin film, supporting self-cleaning under rain or condensation. Its antistatic function also helps reduce dust accumulation.
The coating promotes water spreading across the glass. This characteristic is central to selecting it for a self cleaning glass coating application.
The ultra-thin layer is designed to preserve clear glass transparency, making it suitable for the vehicle glazing and mirrors specified in the product information.
Antistatic performance helps reduce dust accumulation, complementing the coating’s function of reducing dirt and stain adhesion.
The supplied description identifies a pure inorganic material system with weather and wear resistance. This nano glass coating combines nano-silica technology with titanium dioxide particles.
At room temperature, the surface dries in 1–5 minutes. Full curing takes approximately 24 hours, so a dry-looking surface should not be treated as fully cured.
Car detailing uses a dedicated scraping tool. Factory application can use spray coating or roller coating, with plasma pretreatment recommended after glass cleaning.
The product’s defining combination is hydrophilic wetting, an inorganic transparent layer and antistatic performance. These details help buyers distinguish its surface behavior and preparation requirements when comparing glass-treatment products.
Reduced dust and stain adhesion supports the intended self-cleaning function when rain or condensation contacts the coated surface.
The coating is designed to form an ultra-thin clear layer on the specified vehicle glass surfaces without obscuring their transparency.
Separate surface-drying and full-curing times give detailing workshops and factory buyers concrete timing information for planning their application process.
The supported scope includes automotive windshields, side windows, rear windows and mirrors. Consider this treatment when the project calls for hydrophilic surface behavior, reduced dust accumulation and a transparent coating. Do not apply it directly to an existing hydrophobic surface, as this may reduce adhesion.
For car detailing, prepare the glass thoroughly and apply promptly after cleaning to avoid dust contamination. Avoid application during rainy conditions.
Use glass polishing compound to clean the glass surface before coating. Surface preparation is part of the specified application procedure.
Rinse with clean water. According to the product directions, a hydrophilic water film on the rinsed surface indicates that oily contaminants have been removed.
Apply the coating using a dedicated scraping tool. Coat immediately after cleaning to prevent dust contamination; do not coat directly over a hydrophobic surface.
The stated room-temperature surface-drying time is 1–5 minutes, while complete curing takes approximately 24 hours. Keep the two stages distinct when scheduling the work.
For factory processing, use spray coating or roller coating. After cleaning the glass, plasma treatment is recommended before coating. Apply promptly after preparation to limit dust contamination.
| Order reference | GETSUN GT-1238 Glass Nano Coating Agent, 1L bottle |
|---|---|
| Intended treatment | Transparent vehicle-glass treatment combining hydrophilic wetting, self-cleaning support and reduced dust adhesion |
| Process selection | Dedicated scraping tool for car detailing; spray or roller coating for factory application |
| Stated durability profile | The supplied product information states hardness up to 4H+, abrasion durability above 25,000 cycles and a protection lifespan above 5 years. |
For this automotive glass coating, durability figures are stated product specifications, not a warranty promise. Buyers should request the supporting test methods, substrate preparation and applicable conditions when evaluating them for a particular project.
Store at the recommended temperature of 18–25 °C. This is a storage recommendation, not a specified application-temperature range.
This hydrophilic glass coating has a stated contact angle below 10 degrees and promotes water spreading into a thin film. It should be selected for that behavior rather than for water-beading performance.
The product information lists automotive windshields, side windows, rear windows and mirrors. It does not establish compatibility with vehicle paint, plastics or other unlisted substrates.
No. The directions warn against direct application to hydrophobic surfaces because adhesion may be reduced. Prepare the glass using the specified polishing and rinsing procedure before coating.
At room temperature, surface drying takes 1–5 minutes, but full curing takes approximately 24 hours. These are separate stages of the application process.
Specify model GT-1238 and the 1L pack, identify the intended glass and application process, and request relevant technical and safety information. Ask for supporting conditions and methods for the stated hardness, abrasion and lifespan figures, together with quotation and packaging details.
For this automotive glass coating, contact our product team for specifications, packaging information and quotation details .
Have questions about our products or want to discuss a custom order? Our team is ready to help you.