Used XCMG GR165 Motor Grader 16500kg Operating Weight 3960mm Moldboard 165HP Engine Construction Machinery
Used XCMG GR165 Motor Grader Product Introduction
This pre-owned XCMG GR165 motor grader is a versatile mid-size grader suited for secondary road maintenance, construction site preparation, and municipal grading projects. Equipped with a 165HP Weichai WP6G165E22 Diesel diesel engine, this grader delivers precise blade control for finish grading, road maintenance, ditching, slope cutting, and surface preparation. The moldboard features hydraulic angle adjustment, side shift, and tilt functions, allowing the operator to achieve precise grading geometry for road base preparation, gravel road maintenance, and large-area surface leveling. The articulated frame steering combined with front wheel lean provides a tight turning radius and offset tracking capability for ditch cleaning and slope work. The unit has received regular preventive maintenance with detailed service logs documenting oil analysis results, cutting edge replacements, and circle wear measurements.
XCMG GR165 Motor Grader Technical Parameters
| Parameter | Specification |
|---|---|
| Brand & Model | XCMG GR165 |
| Engine Model | Weichai WP6G165E22 Diesel |
| Rated Engine Power | 165HP |
| Operating Weight | 16500 kg |
| Moldboard Length | 3960 mm |
| Moldboard Height | 610 mm |
| Moldboard Thickness | 22 mm |
| Blade Rotation Angle | 360° (Hydraulic) |
| Blade Side Shift (Left/Right) | 650/650 mm |
| Blade Tip Angle (Forward/Back) | 40°/5° |
| Blade Shoulder Reach (Left/Right) | 2100/2100 mm |
| Maximum Lift Above Ground | 460 mm |
| Maximum Cutting Depth | 680 mm |
| Scarifier Type | 11 Teeth, Hydraulic |
| Scarifier Working Width | 1800 mm |
| Scarifier Penetration Depth | 280 mm |
| Front Wheel Lean Angle | ±17° |
| Articulation Angle | ±±25° |
| Turning Radius (Minimum) | 8.5 m |
| Transmission | Powershift 6F+3R |
| Maximum Travel Speed (Fwd/Rev) | 42/30 km/h |
| Tire Specification | 17.5-25 (12PR) |
| Fuel Tank Capacity | 380 L |
| Hydraulic System Pressure | 18 MPa |
| Overall Length | 8800 mm |
| Overall Width | 2600 mm |
| Overall Height (to Cab Top) | 3350 mm |
| Wheelbase (Tandem Center) | 6200 mm |
| Cabin | ROPS/FOPS Enclosed Cab, HVAC, Adjustable Operator Seat |
Grader Condition Assessment
This XCMG GR165 motor grader has been inspected with focus on the unique wear components of grading equipment. The circle (slew ring) was checked for excessive play using a dial indicator — total backlash measured within the manufacturer's service limit. Moldboard cutting edge and end bits were measured for remaining wear life; cutting edge thickness is above the minimum replacement specification. The blade linkage pins and bushings (blade lift, circle shift, blade tilt cylinders) were inspected for clearance with all within acceptable range. The tandem drive chain tension was checked and adjusted to specification. Engine compression and turbocharger performance verified. Transmission clutch pressures measured within range through all gear selections. The articulated frame center-pivot bearing was lubricated and checked with no measurable vertical play. All tires exhibit even wear with tread depth above 50% of new specification. The scarifier hydraulics were tested through full raise/lower cycle with system pressure maintained.
Grader Transport & International Shipping
Motor graders are typically shipped via Ro-Ro (Roll-on/Roll-off) carrier service from major Chinese ports due to their self-propelled nature and extended frame length. For destinations without Ro-Ro service, the grader can be partially disassembled (moldboard removed and packed separately, cab roof externals detached) for flat-rack container transport. Prior to shipment, the machine undergoes a comprehensive cleaning process including chassis pressure wash, engine compartment degreasing, and moldboard surface treatment to prevent sea-spray corrosion. The articulation joint is locked in the straight position with a transport pin. The battery is disconnected and the fuel tank drained to minimum safe level per IMO regulations. Complete export documents will be prepared: commercial invoice, packing list, certificate of origin, and ocean bill of lading. Approximate transit times: Southeast Asia 5-10 days, Middle East 14-20 days, Africa 20-35 days, South America 25-35 days.
Post-Delivery Service & Maintenance Support
A comprehensive pre-delivery inspection document is supplied with the grader, recording all measurement values and observations. We provide 7 days of remote technical assistance after the machine reaches your destination port, addressing any questions regarding start-up procedures, moldboard control calibration, circle rotation mechanism operation, and daily maintenance routines including grease fitting locations and fluid level checkpoints. A recommended wear-parts reference list is included covering: moldboard cutting edges and end bits, scarifier teeth and shanks, hydraulic filter replacement kits, circle wear inserts, and tandem drive chain tensioners. Through our international parts network, we can facilitate express courier delivery of commonly needed spares. The buyer is advised to schedule a local grader technician for arrival commissioning and to verify all blade control calibrations before operational deployment. This machine is supplied in its inspected used condition.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.