RJ45 Network Socket Connector FG RJ-056-1-4 Featuring Brass Shielding and Phosphor Copper Contact Zone

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

RJ45 network socket connector. This product specification covers performance, tests, and quality requirements for RJ45 connectors. All inspections shall be performed using the applicable inspection plan and product drawing.

Product Attributes

Housing Dielectric Material: Refer to drawing
Housing Color: Refer to drawing
Contact Zone Material: Phosphor Copper
Shielding Zone Material: Brass
Revision: A-0
Release Date: 2012-4-16
Prepared by:
Approved by:

Technical Specifications

Category	Item	Requirement	Test Procedure
Requirements	Standard atmospheric condition	Ambient temperature: 15 to 35 Relative humidity: 63% to 67% Air pressure: 86 kpa to 106 kpa	Unless otherwise specified
	Temperature	Operating: -25 to 85 Storage: -40 to 85
	Ratings	Voltage: 125 Volts Current: 1.5 Amperes
	Dimension	Refer to applicable product drawing
Performance and Test Description	Appearance	Product shall meet requirements of applicable product drawing and specification.	Visual, dimensional and functional per applicable quality inspection plan.
	Electrical	Low Level Contact Resistance	Terminal Pin1-Pin8: 40 milliohms maximum initial, 40 milliohms maximum after test Switch: 100 milliohms maximum initial, 100 milliohms maximum after test	Mate subject connector with compatible connector. Then measure and record the contact resistance of the specimen under test with a test current of 100 mill-amperes maximum and 20 mill-volts open circuit voltage maximum.
		Insulation Resistance	500 Mega ohms minimum initial 200 Mega ohms minimum final	After 500 VDC for 1 minute, measure the insulation resistance between the adjacent contacts of mated and unmated connector assemblies.
		Dielectric Withstanding Voltage	1 minute hold with no breakdown or flashover. Voltage: 500 VDC Current leakage: 10.0 mA max.	Test between adjacent contacts of unmated connector assemblies.
	Mechanical	Mating force	25N Max.	Measure force necessary to mate the connector assemblies at a max of 12.5 mm/minute.
	Mechanical	Durability	750 cycles. Shall meet visual requirements, show no physical damage.	Mate and unmated connector assemblies for 750 cycles at a maximum rate of 20 cycles/min.
	Environmental	Heat test	The insulation resistance must coincide previously specification. Shall meet visual requirements, show no physical damage.	Subject mated connectors to 85 2 for 96 hours. It shall be subjected to standard atmospheric condition for 1 hour after which measurements shall be made.
		Steady State Humidity	The insulation resistance must coincide previously specification. Shall meet visual requirements, show no physical damage.	Subject mated connectors to relative humidity of 90% to 95%RH and a temperature of 40 2 for 96 hours. It shall be subjected to standard atmospheric condition for 1 hour after which measurements shall be made.
		Salt Spray	Shall meet visual requirements, show no physical damage.	Subject mated connectors to 51% salt-solution concentration, 35+1/-2 for 8 hours.
	Mounting characteristics	Solderability	Solderable area shall have minimum of 95% solder coverage.	Dip the pin in flux of R type for 5-10 seconds. Immerse the solder pin of the connector in the solder bath at 2455 for 4.0-5.0 seconds.
Mounting characteristics	Resistance to soldering heat	The contact resistance must coincide previously specification. Shall meet visual requirements, show no physical damage.	Reflow Soldering Conditions: Preheat: 180, 20.3 minutes. Soldering heat: Peak temperature 2605 within 10 seconds. Soldering iron method: Bit temperature 35010, application time 1~5 sec.