Durable hanxia HX 10.0 180 ZCJB USB connector rated DC 30V 1.5A with mechanical and electrical performance
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
This document outlines the specifications for the HX 10.0 180ZCJB USB product from Shenzhen Hanxia Electronic Co., Ltd. It details the product's ratings, operating conditions, and performance criteria across mechanical, electrical, and durability tests.
Product Attributes
- Brand: Hanxia Electronic ()
- Model: HX 10.0 180ZCJB
- Origin: Shenzhen, China
Technical Specifications
| Item | Test Conditions | Performance | Specification |
| RATING | |||
| Rating | DC 30V 1.5A | ||
| Standard Atmospheric Conditions | (1) Temperature: 5 to 35 (2) Humidity: 45% to 85% (3) Pressure: 86Kpa to 106Kpa | ||
| MECHANICAL | |||
| Connection Force | After connecting and disconnecting using standard plug gauge 3 times. | 3.57Kgf MAX | |
| Disconnection Force | After connecting and disconnecting using standard plug gauge 3 times. | 1.02Kgf MIN | |
| Terminal Strength | A static load of 0.1N/m (1kgf/cm) applied to the tip of the terminal for 1 min in any direction. No damage to terminal such as cracks, looseness or play. Electrical and mechanical characteristics shall be satisfied. | ||
| ELECTRICAL | |||
| Contact Resistance | Measured at small current (100mA or less) at 1000Hz. | 30m MAX | |
| Insulation Resistance | Apply a voltage of 100V DC for 1 min to following portions: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted. | 1000M MIN | |
| Dielectric Strength | AC 500V rms (50~60Hz) for 1 min. Trip current: 0.5mA. (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted. Without damage to parts, arcing or breakdown etc. | ||
| DURABILITY | |||
| Solderability Test | The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds. (1) Solder wetting time shall be 3 sec or less. (2) The area of soldering should be over 75%. | ||
| Resistance to Soldering Heat Test (Reflow Soldering) | Preheat: Temperature on the copper foil surface should reach 180. 120s after PCB entered into soldering equipment. Tallest Temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 within 20 seconds. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | ||
| Resistance to Soldering Heat Test (Soldering Iron) | Bit temperature 3305. Application time of soldering iron 30.5 sec. However, excessive pressure shall not be applied to the terminal. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied. | ||
| Humidity Test | The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then maintained at standard atmospheric conditions for 1 Hr for other procedures. No damage on appearance. Mechanical and electrical characteristics shall be satisfied. | ||
| Heat Test | The jack shall be stored at a temperature of 702 for 96 hours, and then subjected to controlled recovery conditions for 1 hour. No damage on appearance. Mechanical and electrical characteristics shall be satisfied. | ||
| Cold Test | The jack shall be stored at a temperature of -253 for 96 hours and then subjected to controlled recovery conditions for 1 hour. No damage on appearance. Mechanical and electrical characteristics shall be satisfied. | ||
| Life Test (Without Load) | Connection and disconnection shall be made with mating plugs and jacks for 5000 cycles at a speed of 10 to 25 cycles/min. | (1) Contact Resistance: 0.1 (2) Disconnection Force: 0.8 to 2.0N (3) Mechanical and Electrical Characteristics: Shall be satisfied. | 5000 Cycles |
| Life Test (Load) | Connection and disconnection shall be made 5000 cycles at a speed of 10 to 20 cycles/min at rating condition (non-inductive load). | (1) Contact Resistance: 0.1 (2) Disconnection Force: 0.8 to 2.0N (3) Mechanical and Electrical Characteristics: Shall be satisfied. | 5000 Cycles |
| Temperature Cycling Test | The jack shall be subjected to 5 cycles of the following conditions, then returned to room ambient condition for 30 minutes. No deformation or cracks in molded part. | Insertion & Extraction Force: 3 to 20N Contact Resistance: Max. 30m Insulation Resistance: Min. 100 M Dielectric Withstanding Voltage: 100VAC/min (between terminals) | |
| Cold & Heat Shock Test | The jack shall be subjected to 5 cycles of the following conditions, then returned to room ambient condition for 30 minutes. No deformation or cracks in molded part. | Insertion & Extraction Force: 3 to 25N Contact Resistance: Max. 30m Insulation Resistance: Min. 100 M Dielectric Withstanding Voltage: 500VAC/min (between terminals) | |
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Hefei Purple Horn E-Commerce Co., Ltd.
Location
Room 1306B, Building A, Xindi Center, Qimen Road, Hefei City, Anhui Province
Contact Person
Sellina