USB connector hanxia HX AF 90 ZJDG JB offering robust connection and insulation resistance properties

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

The HX AF 90ZJDG JB is a USB connector manufactured by Shenzhen Hanxia Electronic Co., Ltd. It is designed for use within a practical temperature range of -25C to 85C.

Product Attributes

Brand: (Shenzhen Hanxia Electronic Co., Ltd)
Origin: China
Model: HX AF 90ZJDG JB

Technical Specifications

Item	Project	Test Conditions	Performance	Specification
Mechanical	Connection Force	Measured after connecting and disconnecting using standard plug gauge 3 times.		35N MAX
Mechanical	Disconnection Force	Measured after connecting and disconnecting using standard plug gauge 3 times.		8N MIN
	Terminal Strength	A static load of 0.1N/m (1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. There shall be no damage to the terminal such as cracks, looseness or play. Electrical, and mechanical characteristics shall be satisfied.
Electrical	Contact Resistance	Measured at small current (100mA or less) 1000Hz		30m MAX
	Insulation Resistance	Apply a voltage of 100V DC for 1 min to following portions after which measurement shall be made: (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted		1000M MIN
	Dielectric Strength	AC 500V ims (50~60Hz) for 1 min Trip Current: 0.5mA (1) Between body and conductor (2) Between conductors not to be contact (3) Between conductors not to be when plug is inserted. Without damage to parts arcing or breakdown etc.
Durability	Solderability Test	The top of the terminals shall be dipped 1mm in the solder bath of 2505 for 50.5 seconds. (1) Solder wetting time shall be 3 sec or less (2) The area of soldering should be over 75%
	Resistance to Soldering Heat Test (Reflow Soldering)	Preheat: Temperature on the copper foil surface should reach 180, 120s after the P.C.B entered into the soldering equipment. Tallest temperature: Temperature on the copper foil surface should reach the peak temperature of 2605 with in 20 seconds. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
	Resistance to Soldering Heat Test (Soldering Iron Method)	Bit temperature 3305 Application time of soldering iron 30.5 sec. However excessive pressure shall not be applied to the terminal. Without deformation of case or excessive looseness of terminals. Electrical characteristics shall be satisfied.
	Humidity Test	The jack shall be stored at a temperature of 402 and a humidity of 90% to 96% for 96 Hr, then the jack shall be maintained at standard atmospheric condition for 1 Hr for other procedures.	Appearance no abnormality, mechanical and electrical characteristics shall be satisfied.
	Heat Test	The jack shall be stored at a temperature of 702 for 96 hours, and then it shall be subjected to the controlled recovery measurement. Appearance no abnormality, mechanical and electrical characteristics shall be satisfied.
	Cold Test	The jack shall be stored at a temperature of -253 for 96 hours and then it shall be subjected to the controlled recovery conditions for 1 hour after which. Appearance no abnormality, mechanical and electrical characteristics shall be satisfied.
	Life Test (Without Load)	Connection and disconnection shall be made with the mating plugs and jacks for 5000 cycles at a speed of 10 to 25 cycles/min.	(1) Contact Resistance 0.1 (2) Disconnection Force 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
	Life Test (Load)	Connection and disconnection shall be made 5000 cycles at a speed 10 to 20 cycles / min at rating condition (non-inductive load).	(1) Contact Resistance 0.1 (2) Disconnection Force 0.8 to 2.0N (3) Mechanical and electrical characteristics shall be satisfied.
	Temperature Cycling Test	The jack shall be subjected to 5 cycles of the following conditions showed in the figure, and then shall be returned allowed to remain in room ambient condition for 30 minutes.	No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 20N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 100VAC/MIN (between terminals).
	Cold & Heat Shock Test	The jack shall be subjected to 5 cycles of the following conditions showed in the figure, and then shall be returned and allowed to remain in room ambient condition for 30 minutes.	No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 25N. Contact Resistance: Max. 30m. Insulation Resistance: Min. 100 M. Dielectric Withstanding Voltage: 500VAC/MIN (between terminals).