connector strip HCTL HC-XG-2*15Y-05 suitable for electronic projects requiring 2.54 mm pitch spacing

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This specification covers the 2.54 series connector strip, including product performance, test methods, and inspection requirements. Designed for reliable electrical connections, these connectors are suitable for a wide range of electronic applications.

Product Attributes

Brand: HCT ()
Origin: Shenzhen, China
Certifications: ROHS
Material: PBT, Phosphor bronze, Brass
Color: Black, White

Technical Specifications

Item	Requirement	Test Mode
4. Appearance and Dimension
Appearance	Product surface without defect, dirt, crack, and mechanical damage; Contact without rust plating, oxidation, and peeling.	General Principles
Dimension	According to drawings	According to drawings
Exchangeable	Exchangeable with same specification products.	-
3. Use Condition
Ambient temperature Range	-25 85	-
Applicable Wire Sizes	AWG #2226	-
Applicable PC board thickness	1.6mm	-
6. Electrical Performance
Rated Voltage	250V AC/DC	-
Rated Current	3A AC/DC	-
Withstand voltage	No breakdown or flashover	Apply 500V AC(rms) for 1 minute and the leakage current shall not exceed 0.5mA to the adjacent terminal and ground of the mate connectors
Contact Resistance	20m (Initial value)	A maximum voltage of 20mV and maximum current of 100mA are applied to the Mate connector (Does not include wire resistance)
Insulation Resistance	1000 M	Apply 500V DC(rms) for 1 minute between adjacent contacts to measure the insulation resistance
7. Mechanical Performance
Single contact insertion force	3.5N	The housing together with the terminal ends with wafer matched at a rate per minute to 253mm inserting force test
Single contact Withdrawal force	0.39N	The terminal and the hole seat at a react per minute to 253mm along the write direction are pulled out from the hole in the seat capacity
Terminal crimping Wire strength	10N (AWG#22) / 30N (AWG#24) / 20N (AWG#26)	Axial per minute to 25 3mm rate of the pullout force
Pin Retention Force	10N	Exerts a force on the pin end at a rate per Minute 253mm until the needle exit
Durability	Contact Resistance 40m	Mate connectors up 30 cycles at a Maximum rate of 10 cycles per minute prior to environmental test
Vibration	Current Interruption: 1 sec Max; Contact Resistance 40m	Amplitude 1.5mm p-p; Frequency :10-55-1O Hz/minute; Period: 2hour for each direction (X, Y, Z axis)
8. Endurance Characteristics
Thermal Aging	Appearance: No damage; Contact Resistance 40m	Temperature852; Period96 hours continuously
Constant Humidity	Appearance: No damage; Contact Resistance 40m; Insulation Resistance 1000m	Relative humidity90-95% (RH); Period96 hours continuously; Temperature:402 C
Temperature Cycling	Appearance: No damage; Contact Resistance 40m; Insulation Resistance 1000m; Withstand voltage: No breakdown or flashover	One cycle consists of -553C 30min, room temp 10-15min, 853C 30min, room temp 10-15min. Total cycle: 5 cycles.
Salt Spray	Appearance: No damage; Contact Resistance 40m	Temperature : 35 3 C; Concentration: 5 1 %; Period: 24H
Solder ability	Soldering area: 90 %	Solder temperature 245 5C; Immersion period:3 0.5S
Resistance to soldering heat (Wave soldering)	Appearance: No damage	Soldering temperature2605; Soldering time50.5S
Resistance to soldering heat (Manual soldering)	Appearance: No damage	Soldering pot3505; Soldering time30.5S