electronic speaker socket connector JINJIA XLR-11-N3B with rated voltage 50V AC and current up to 7.5A

Name: electronic speaker socket connector JINJIA XLR-11-N3B with rated voltage 50V AC and current up to 7.5A
Brand: Hefei Purple Horn E-Commerce Co., Ltd.

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

XLR JACK (Combo) SPECIFICATION

This specification applies to XLR jack (Combo) which is used in electronic products. It is designed for speaker socket connectors in electronic devices.

Product Attributes

Brand: Shenzhen Jinjiarun Electronic Technology Co., Ltd
Origin: Shenzhen
Document Number: JJR-WI-46
Issue Date: 2008-09-10
Version: A1

Technical Specifications

Item	Property	Test Condition	Performance
2. Rated /
2-1. Practical temperature range	Applicable temperature range		-30 to +80
	Humidity range		85% RH.MAX.
2-2. Preservation temperature range	Storage temperature range		-10 to +40
	Humidity range		85% RH.MAX.
	Storage environment		Surrounding air without acid, alkaline or other corrosive gases. Storage period not exceeding 180 days.
2-3. Rated voltage and current(MAX.)	Maximum rated voltage and current		50V AC, 3A(Type A) / 7.5A(Type B)
2-4. Appearance	Surface condition		No scratches, soil, rust or discoloration.
4. Electrical efficiency /
4-1 Withstand Voltage	Withstand AC voltage	Between two non-contact terminals for 1 minute	1500V (50/60Hz RMS). No dielectric breakdown shall occur.
4-2 Insulation Resistance	Insulation resistance	Apply 500V DC between any contactless terminal and the other terminal for 1 minute 5 seconds.	10000 M Min.
4-3 Contact Resistance	Contact resistance	Measure at the tail end of each terminal (voltage max. 20mV, current max. 100mA) for a pair of matched terminals.	30 m MAX.
5. Mechanical Performance /
5-1 Insertion and withdrawal forces	Insertion/withdrawal speed		2 mm/s
	XLR	Mating of complete connectors without the effect of any latching or retaining device	Insertion: 35 N max. Withdrawal: 2 N min.
	JACK	Mating of complete connectors without the effect of any latching or retaining device	Insertion: 40 N max. Withdrawal: 5 N min.
5-2 Terminal Strength	Strength test	Each terminal should withstand a force of 0.5 kgf for 10 seconds.	No looseness or damage. Terminal deformation is acceptable.
6. Durability /
6 Life test	Life cycle	Under no load, rotate and then plug in, rotate and then pull out with a matching plug for 1000 times at a frequency of 5 times per minute.	No obvious change in appearance or destruction. Contact resistance: less than 50 m.
7. Solderability /
7-1 Resistance to soldering heat	Soldering condition	Dip terminal in solder at 2603 for 51 seconds.	Plastic base should not be deformed, and terminals should not fall off.
7-2 Solderability	Soldering condition	Dip in solder at 2453C for 30.5 seconds.	Solder coating area should be more than 95%.
8. Environment test /
8-1 Cold test	Condition	Place housing at -30 3 C for 96 hours, then under standard atmospheric conditions for 1 hour.	Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
8-2 Heat test	Condition	Store housing at 802 for 96 hours, then under standard atmospheric conditions for 1 hour.
8-3 Humidity test	Condition	Store housing at 403 with 90% ~ 95% RH for 96 hours, then under standard atmospheric conditions for 1 hour.	Appearance: No obvious change. Contact resistance: 50 m max. Insulation resistance: 500 M min. Withstand voltage: AC 1000V.
8-4 Temperature Cycling	Condition	Place Jack under specified conditions, then in room temperature for 30 minutes.
8-5 Salt spray test	Condition	Temperature: 35 2. Solution: 5 1% salt. Spray time: 24 hours. Wash and dry at room temperature after experiment.	Appearance: No obvious rust.
9. Test condition /
General conditions	Temperature, Humidity, Atmospheric Pressure	15C to 35C, 25% to 85% RH, 86 kPa to 106 kPa.	For doubtful judgments: 201C, 63% to 67% RH, 86 kPa to 106 kPa.
10. Amendment /
Procedure	Specification changes	Negotiated and agreed by manufacturer and customer.
12. XLR JACK (Combo) TYPE /XLR
Type	Description		Type A, Type B